1997 Vortec 5.7

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 7, 2006
Threads
11
Messages
84
Location
Savannah, GA
Been a landcruiser guy for a while however,

1st Post..... 1st stupid question....

Looking for a replacement motor for my carbed V8 in my 70' FJ40... is $1250 a good price for a 5.7l V-8 Vortec out of a 1997 GMC pickup? Motor/wiring harness/brain box basically a turn key motor..

All comments welcome....:D
 
Before I started my body off resto (kinda) I looked into vortecs for my 78 instead of rebuilding the 2F. I ended up rebuilding the 2F but depending on miles, that seems reasonable. Most I found at local yards wanted about a grand for an under 100k vortec. Some of these guys might tell you to run, but for most hobbyists that can't get lucky enough to find cheap or free stuff I would say that's about a fair price.

:cheers:
 
That is a reasonable price as long as the mileage is not over 100k. I am biased (have three of them) but these are excellent motors for Cruisers.
 
x2 on the vortec. I paid a local shop to rebuild my 2f a few years ago. It was bored .030 over, ported and polished head, 3 angle valve job, had an rv cam installed, an electronic ignition, headers, etc, etc. It was a torquey little beast, and I loved it- all 6k miles of it before it gave up the ghost!! (it lasted 2 years- warranty was for 1 year...) 2nd time around, I scored a 2001 5.3 vortec out of a Tahoe complete with ALL accessories and wiring harness w/only 9 miles on for $1900. from Schram Auto Parts. It has so much more power! I wished I'd done this the first go around! 12k miles later she still purrs like a kitten and bites like a lion!
 
I'm looking at doing the same. I found a 5.7 out of a 99 Suburban. They want $1900 for the engine, 4L60E tranny and all wiring and computers. This engine has 80K miles. I have also looked into a 4.3 V-6 vortec. I can get the 4.3 with a NV4500 and all wiring for $2000. The 4.3 only has 18K miles.
 
I had a V-6 vortec in my 1995 Chevy 1500... It was a very strong motor. I wouldn't hesitate to put one in a cruiser. Well, actually that's a lie, I love my 2F and will never part with it. But if I was going to swap an engine, I'd definitely do a vortec.
 
for the record, I bought an ebay 93' 350 for 250$ and got the computer and wiring harness. Checked it out and found bad compression so I sent it to GMGoodwrench as a core and got a remanufactured for 1600$ total. That was one way to do it.
 
Thanks...

Thanks for the inputs... I've been looking for a while and reading alot in the last year.. I still want to keep my SM465 behind it even though I know NV has a 5th gear which would help my DD for the last 14 years I've owned it. She's tired and old and needs a new motor.... it's way overdue.

I may end up going with a carbed V8.... still on the fence.

I need a shove... any takers..:)

Cheers
 
as far as off road performance, and really on road for that matter, fuel injected is going to beat carbed hands down everyday of the week. So, if you've got the $ and the resources, I say go with the vortec over the carbed V8. I think you'll be very pleased with the vortec's performance, they're quite the engine. JMHO
 
Just thought I'd chime in with my two cents. I have a 96 5.7 Vortec in my truck that is my daily driver. I have 225000 miles on the truck and have had great luck with it. I have not done any major work on the engine and as soon as my carb 350 in my 40 goes out, I'll be replacing it with a Vortec. Basically i'm saying that I wouldn't be scared off by 100k miles. Maybe I'm lucky, have any of you had problems with the Vortech over 100k?

zglad
 
I have a '97' Astro with the 4.3 vortec. It has 170k on it now and still going strong. At 100k I put a new alt on it, at about 150k it needed a cat converter and a distributor. No other probs! I love it! I used to have a '79' Ford 150 with the 400 big block, no comparison! The 4.3 will outpull the 400. Sold the Ford to a friend who had a travel trailer about the same size and weight as ours. I could outpull him up Suttle Lake grade on Santiam Pass hands pown any day with the 4.3 while towing the trailers. When I get to the place that I need to redo the motor in my 40 the 4.3 vortec will be at the top of my list! No direct experience with the 5.7, but if it is anything like the 4.3 you can't go wrong if the motor is in good shape.
 
Too bad you're not in the Northeast, I have a 2002 4.3 Vortec with 18,000 miles. ECM and harness included to the first $1,000. I need to make room in the garage for my project.
 
Last edited:
Update #s

I looked around can get a

5.7 Vortec w/ 99k with brains and harness for $1000

5.7 Vortec w/ 23k no brains or harness for $1100


I'm putting this where a carbed 72' block 350 is.

Any thoughts would be appreciated.

I'm trying to get this done before I PCS to GA

Cheers,
 
buy the one with 23k .get an ecm for 100.00 from the local wrecker .ship it to fuel injection specialties they'll reprogram and build you a harness which only needs minor wiring hook-up . and your set. I would try to get the 02's from the donor though . they are $$$ you need the 2 pre-cat ones. The other two can be programmed out. also make sure you get the maf sensor as well . it should be with the rest of the intake tubing.
 
HogDriver?

HogDriver said:
Update #s

I looked around can get a

5.7 Vortec w/ 99k with brains and harness for $1000

5.7 Vortec w/ 23k no brains or harness for $1100


I'm putting this where a carbed 72' block 350 is.

Any thoughts would be appreciated.

I'm trying to get this done before I PCS to GA

Cheers,

Okay, correct me if I'm wrong, but are you an A-10 guy? I was a U-2 crew chief and knew some A-10 guys from germany. They didn't like the dragon.
 
Back
Top Bottom