1/4" Rear Bumper...overkill?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 18, 2004
Threads
259
Messages
1,501
Location
Pacific Northwest
Going to get a rear bumper/tire carrier put together shortly. I purchased the spindles from 4x4 labs and the latches from McMaster. I read that Slee uses 3/16 grade 80 steel, not sure about Hanna or 4x4 Labs. 1/4" will add about 40 pounds vs. 3/16". So as stated above is 1/4" overkill? I plan on 3/16" for the tire carrier/water carrier. Also anybody have some good rear bumper pictures from the ground looking up towards the chasis?
 
Last edited:
A good example of overkill in some of his stuff is "4+" stuff that Man-A-Fre carries. He uses 1/2" steel in some of his bracketry. It's heavy, confidence is high, but for my 80, I'm very happy with the Kaymar bumper. I've abused it, hit it hard and only caused surface scratches. I would say it's thinner than 3/16" but I'm not sure as it's probably metric based measurements.

40 lbs is about the same as 5 gallons of gasoline for a data point.

Dan.
 
1/4" is probably thicker than you need.
It really depends on how you're building.

I ran a bumper made of 1/4" squarewall tubing on my 60 for a long time. It took massive abuse a couple of times, no problems.

I would bet that 3/16 would have done just as well and probably saved me a very little bit of fuel money over 5 years.

Also the 3/16 is cheaper than 1/4, and easier to work with.

But ... it all depends on what you need the bumper to do!
 
I'd say 1/4" for the main body would be overkill. Attachment points, corners, drag points, etc. that'd be good (or thicker). Guy in our club made a bumper kit, the main channel was 1/8", D-ring points were 1/2", and side wings were 1/4", worked great.
 
Last edited:
I agree with Trunk Monkey. Heavier steel on the attachment points and/or structural points, but lighter weight on most of it should do the trick. I saw a bumper on an Xterra once that used 1/8" channel, but they ran a thin wall round tube (about 3/4" diameter? I think) along the bottom corner of the channel, inside. That is- from behind you couldn't see it at all. But if you looked from the spare tire, then the round tube was inside the channel, on the bottom. I would guess that would make the bumper a lot stiffer... but I'm not sure how much.

Probably a lot easier to just use 3/16" wall channel.
 
You've seen my front bumper that is all 1/4". My rear that I have started is all 1/4" too. If you have it, use it!:beer:
 
Hmmm
I've seen pics of Waterjet's front bumper. Looks **amazing**.

Having said that, I'd rather shave 100lbs (50 front, 50 rear) off of the truck if possible. I know that 100lbs isn't a lot, but 50 lbs here and 50lbs there starts adding up.

at the end of the day, the 1/4 vs. 3/16 debate is a pretty minor point--- design and finish will matter a lot more in your overall satisfaction with a given mod. IMHO.
 
I would be inclined to go with the 1/8 and add a few extra stiffening gussets on any week points you suspect. The bar will be half the weight of 1/4in but just as strong if bracing is well placed.
 
My last rear bumper build was 1/4" and I used 3/8" brackets to mount it to the frame. It was super heavy and total overkill, but the metal supply shop had the right length of 4" x 3" (1/4 wall rectangular tubing) in stock....so I used it.

Going heavy can make it a bit harder to work with as you will need a better welder for good clean penetration. Also, if you have any distortion in the welds (mounting brackets) you might be stuck with it as even a 20lb sledge might not give you the minor corrections with the barckets to square it up if you screw up.

Mine worked out perfect, but I had a welder friend put it together after I cut out all the parts and laid it up with the clamps.

All that said, put the weight where you will use it. If you plan on draging your butt over rocks all the time or winching up Mount Everest backwards go for it.

It only cost me $100 and some time.
 
keep in mind these landcruisers are not s-10 blazers, 1/4"fits the bill. 3/4" attachment along with a stout 1/4" box bumper is the only option in my opinion. 3/16" is substandard for an offroad vehichle unless its there for asthetics and to just carry a tire. Just my opinion.
 
keep in mind these landcruisers are not s-10 blazers, 1/4"fits the bill. 3/4" attachment along with a stout 1/4" box bumper is the only option in my opinion. 3/16" is substandard for an offroad vehichle unless its there for asthetics and to just carry a tire. Just my opinion.

Damn dude, just cause some cruisers are affectionately referred to as "pigs" doesn't mean you have to help their weight live up to the name.

1/4" for areas that will meet rocks, i.e. lower edges of wings and bottom of rear section is sufficient and not unnecessary.

3/16 and 1/8 are more than sufficient IMO for other areas that only see load stresses and not impacts.

Most winch bumpers you see in the mini-truck market are made of 1/8" wall 1.75 DOM tubing. Granted a mini-truck weighs 1-2k lbs less than a cruiser, but still, the stuff is very beefy.

When I make my rear bumper I will be using 3/16 wall 1.75 DOM for the main section of the bumper and 1/8 wall 1.75 DOM for everything else. It's just not necessary IMO to go heavier.

Ary
 
gotta back Arya up (and myself too) on this one--

I spent over a year driving my 60, almost every single day, offroad way more than on.
It was heavy (weighed in near 7,000lbs), loaded with gear and water and such. Hit more stuff in reverse than I care to admit (including smashing a concrete wall once). Never even dented the 1/4" 3x5" square tube bumper.

Scratched it pretty deep in a few places.

But never dented.

It was held on by 1/4" supports, sported 1/4" quarter panel protection, and was also screwed into the stock crossbar.

If I planned to use it as an earthmover... I'd build the same size/thickness again. Otherwise, there's just no reason to add that much extra weight that far from the axles. It doesn't really gain you anything.

Now, if you can show me someone who has mangled a well-built 3/16" bumper. Ok, I'll reconsider my position.

But as it stands, I'm of the opinion that using 3/16" or even 1/8" with some gussets is plenty strong for the vast majority of uses and users.

My old bumper weighed in at a solid 150lbs. If it had been made of 1/8" with just a little extra strengthening, it would have probably held up just as well, and I could have thrown two fuel cans on the back and been at about the same weight.
 
Sounds like the Consensus is to use 3/16 with lots of gussets. Also plan on using the factory mount points with grade 8.8. After reading it sounds like the recovery points should be welded directly to the frame rails---how stout of material should we use here....1/2 or even 1"?

Also when welding on the cruiser is disconnecting the batteries enough or should I disconnect the computer as well?
 
Last edited:
if you can incorporate the recovery points into the bumper as the attachment points, you can use bolts vs. welding.

I'm going to leave most of the other observations to the many folks on this board who actually do fabrication work as they know more about than I do.

I'd say just keep in mind that bigger is only better to a point, then it is just bigger and heavier, more expensive and harder to work with/fit.
 
I would NOT weld the recovery points to the frame directly. The quality of weld you can obtain under the truck as opposed to on a work bench is one factor that influences my decision. The other is that I've never seen anyone anywhere recommend welding a recovery point to a truck. Always bolt-on, even if there are welds incorporated into the actual construction of the bolt-on recovery point.

Ary
 
Back
Top Bottom