80 chassis

G'day guys, I'm looking at going all out on my 75 series landcruiser I was wondering if anyone had a suggestion or knew how to get 37" tyres or preferably 38.5" tyres under it, currently im thinking of doing a 80 series chassis swap or doing a coil conversion with 79 series axles but still can't...

I have 1997 Land Cruiser 80 series front and rear axles and frame (rolling) for sale. The frame comes with a clean CA title. Great for someone looking to body swap an 80 series chassis. All parts have no rust. Rig had 170k miles. $3900 for everything

1997 FZJ80 rolling chassis. Great candidate for 40/80 or 60/80 project. Frame & axles have been gone over with wire brush & wheel and have 2x layers of POR15 (following instructions) applied. They are locked axles w/rebuilt knuckles. Actuators work & engage. Has all the wiring and 4x4 computer...

Primarily looking for the front coils C59-222V but depending on price would consider buying a full set of 222V and 269V. Can travel a little ways, but would prefer to keep local to an extent (Charlotte area)

First time poster Is it possible to put a fj62 body onto a 80 series? I’m not just talking about swapping the chassis from the 80 to the 60, I’m talking about just the body of the fj62 and taking off the 80 body and leaving everything there such as driveshaft, engine, fuel system, brake lines...

Hey Land Cruiser Guru's I'm in need of a little help. I'm head deep into a 1988 FJ62 build. I've started to head down the frame swap road - I had been looking at a fj80 chassis, but with where the part out is and where my build is, timing isn't working out. SO..... Anyone happen to have a...

Hello! Couple (new) questions... 1) Just got some new window runs shipped from UAE for the front windows (slow up/downs) but before I start this project I wanted to get a difficulty level for this job? More concerned with braking something along the way when pulling the doors apart than...

hey guys - I'm doing a conversion of my 62 and looking for a good condition 80 roller (would consider just chassis and axles) to build on. I’m located in NJ. Willing to work out shipping as well. thanks

Hey everyone, I searched and yes, I found a ton of articles. The problem is, im an idiot and still don't know exactly what to do. Ive attempted to do probably the simplest install and can't even seem to get that right. sigh. Installing a pioneer double din unit. The guys at Best Buy tossed me...

Howdy, wanting to know what is required to weld 200 series body mounts to my 80 series and if that is even possible. I've seen on 4wd Action Australia that Shawno put 200series mounts on a 80 series chassis (the new dirty 30) but they just said that's what they did, there we no details as to how...

Hey ladies and gents.. First time reader and first time posted. Been reading bits and pieces on the forum for about 4 hours now haha! But thought I'd start a new thread and get some fresh information. I'm in Australia. And I'm looking for any information, steps taken and photos of anyone...

Set of 4 pads for 92-97 FJ/FZJ80 still in factory bubble wrap. $30 plus shipping. 46550-60040 x2 46580-60030 46540-60030 I'm tired of storing them. PM me if you want them. Thanks, Scott

Im parting out my LX450 at fair market prices. Let me know what you need. Located in the Silicon Valley. San Jose to be exact. Engine is on its way out tomorrow. Axle housings were stripped down, hot tanked and sand blasted. Gears and bearings removed from the diffs (Was preparing to regear)...

Hi all, Starting to do a 4 door troopy type of thing. Aquala call them quad cab, so I will call it the same. I like the look of their one so heading towards that look, but being in Australia it's price prohibitive to ship that body here otherwise I would. Started off with a 1984 FJ45 ute in...