My LC has turned into Christine....Help!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I would call Tom and change the order for contacts. Not sure why you are ordering a new starter???
 
I've read a few posts on this happening even after the contacts were replaced (could be due bad installs), so I'm just gunna play it safe and get an emergency cutoff anyways ;)

Nothing wrong with an emergency cutoff, it would have saved some panic for my wife and made that disconnect easier. But if I knew last week what I know now I would have done the PM when I had the time and money rather than when I am forced to do it by a failed part. It could have been pretty ugly had my wife not thought quickly and had a wrench handy.
 
I would call Tom and change the order for contacts. Not sure why you are ordering a new starter???

I'm worried about the solenoid being/going bad, or other damage that may have been caused by it running for several minutes. Are the worries not really justified? I don't have any experience with this, so I welcome your input.
 
I'm amazed. Tell your wife that I'm truly impressed that she thought about disconnecting the battery. Not many guys out there who would have thought of that...
 
I'm worried about the solenoid being/going bad, or other damage that may have been caused by it running for several minutes. Are the worries not really justified? I don't have any experience with this, so I welcome your input.

You might give it a visual once over, but I think the UPS truck comes at 3PM so it may be moot anyways. Starters are big $$$, contacts are small $.
 
I'm amazed. Tell your wife that I'm truly impressed that she thought about disconnecting the battery. Not many guys out there who would have thought of that...

I'm amazed she could find the wrench!!! It's in the bottom of my recovery bag - straps, hand winch, tie downs, etc.
 
More props for my wife...on top of all this, she made me lunch, gave the dog a haircut, and is mowing the lawn as I type.

Cruiser is in front of the house, I should have the starter off before long. I'll pick up a rebuild kit from Chic's armature in town. I've ordered the starter from Tom at American Toyota, it'll be here on Friday. That way if the rebuild doesn't work I'm not out of my vehicle for too long and I can fix it up good on Saturday. If the rebuild does work, there might a 2.0 starter for sale for a little less than you can buy it elsewhere.
 
I'm worried about the solenoid being/going bad, or other damage that may have been caused by it running for several minutes. Are the worries not really justified? I don't have any experience with this, so I welcome your input.

The starter is a small electric motor, in order to turn the engine it's way geared down, count the teeth in the ring gear vs starter gear, there are also gears in the front of the starter case. When engaged and turning the engine to start it, the starter motor is running at it's rated rpm. When the motor starts the solenoid disengages the starter. If, as in your case the contacts stick and don't allow it to disengage, the engine drives the starter, turning it at much higher than rated rpm.

This high speed operation can cause a couple of problems. The most common is the armature violently disassembling it's self. This is noisy and usually accompanied by an electrical short, smoke and possibly fire! If this happens the starter will no longer work. The other issue is the over speed of the gears and bearings, most of the time it doesn't damage them, just disassemble the gear case part of the starter and regrease.

Toyota starters are very robust, can take a bunch of punishment. The plan that I have always used with good effect is; At about 60K+ miles replace the contacts and clean the plunger. At 120K+ I replace the contacts, plunger, disassemble the starter, inspect, regrease the gears and bearings. Using this plan have had very little problems with them, very rarely even seen bad brushes in them.
 
Thanks Kevin. I'll work on it and take some pictures disassembled and go from there.
 
Feeling a little sheepish here, Anybody have a tip for removing the clip on the starter connector? 1 connector has a 12mm nut, 1 has a 13mm nut, and the last has a clip. Figured out the nuts, I guess that gets me another banana, but I don't want to break the clip connector on the 3rd and it's not budging.
 
I got it, just couldn't do it from the angle I was at. Removed the tire and it was easier. Done for today. Will take it apart tomorrow and pick up the rebuild parts from Chic's. Thanks all!
 
Last edited:
Back
Top Bottom