Carb Rubber Grommet thingy

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 19, 2005
Threads
48
Messages
807
Location
Fountain hills, AZ
Carb Rubber Grommet thingy *Pics added*

On the throttle linkage where is attaches to a braket on the firewall keeps falling out, anyone on mud now of a why to fix it so it won't?
 
Last edited:
Some pics to help show what I am talking about, when the grommet is out my idle is about 1150rpms...


pic3.jpg


pic2.jpg


pic1.jpg
 
There's supposed to be a rubber grommet that snaps into that hole where the linkage goes through the bracket. See item 61 on This page (SOR). That's what should be there. Or are you asking about that rubber piece in pic 2 (which I don't think is stock)?

(Scroll down to Accelerator Linkage -- 9/73-1984 40 & 55 Series section and look at expanded pic on the right side of the page).
 
Last edited:
GetsUThere said:
There's supposed to be a rubber grommet that snaps into that hole where the linkage goes through the bracket. See item 61 on This page (SOR). That's what should be there. Or are you asking about that rubber piece in pic 2 (which I don't think is stock)?

I think that's a pointer to the linkage (but I don't know). I guess I need some of those too!

:doh:
 
Yes that groment.....sometimes when this is absent it will mess with your idle at stop/go traffic. I ordered some through the toyota dealer. About only bad thing about Sor is they will kill you on shipping/handling pratices.

If they don't don't sell it for that year model sometimes changing to a new year model may help or ask to look it up in the fj60 section.
 
Relix said:
yeah it's a 7/11 straw to help point things out....yeah it looks like Part #50 in that diagrahm

No, part 50 is the rubber that the bracket mounts on. Here's a picture of one I had sitting around. See how the mounts (part 50) have the steel tubes (part 57) in them? Part 61 is shown at the top of the bracket on my pic where the accelerator linkage goes.
p8010004a.webp
 
you can cut a vac hose and slip it over the rod end then install into bracket. then place steel washer and then key pin into hole....:cool:
 
Yes. And it will fill that large empty hole by the straw in your pic 2. I just noticed the part in my pic is upside down of how it's mounted in a cruiser, so don't let that confuse you as how that relates to yours. The round area by the straw is the same as the round area as at the top in my pic. The rubber part there (61) is missing in yours. That'll keep that end of the linkage from having so much slop in it. The grommet shouldn't fall out unless it has completely deteriorated.

The other end of the linkage should be restrained by a washer and cotter pin. (That's not really shown in the SOR pic). The carb end shouldn't be able to move front to back very much at all.
 
Last edited:
Not to hijack, but I have the same issue. My throttle gets stuck and I can't seem to diagnose the problem. Comparing my linkage to those seen in this thread, I am assuming #1 is the part in question. Also, #2 looks to be an odd PO mod.
Linkage[1].webp
 
DallasFJ40 said:
Not to hijack, but I have the same issue. My throttle gets stuck and I can't seem to diagnose the problem. Comparing my linkage to those seen in this thread, I am assuming #1 is the part in question. Also, #2 looks to be an odd PO mod.

DallasFJ40,
this is a picture of two different accelerator rods that I have. The bottom one is the same as the one on my 77. The top one I think came off a 79. Yours definitely has been modified by somebody.
p8020007a.webp
 
GetsUThere said:
DallasFJ40,
this is a picture of two different accelerator rods that I have. The bottom one is the same as the one on my 77. The top one I think came off a 79. Yours definitely has been modified by somebody.

That explains why my throttle sticks/goes crazy. I often have to back it up with my foot to slow it down. I also have an accelerator return spring attached to the bottom of the accel. rod, connecting it to an open bolt hole below. I guess I need to locate the correct linkage. Yours looks pretty new, where did you get it?
 
The bottom one came from a box of random stuff on ebay. It's bent so I'm not planning to use it. The top one also came from ebay, but it was real rusty when I got it. It's been sanded and put through a vibrating polisher. It's going on my 80 once I round up enough parts to put a stock carb back on it. For the moment I haven't figured out what to do for a finish on it yet.
 
GetsUThere said:
DallasFJ40,
this is a picture of two different accelerator rods that I have. The bottom one is the same as the one on my 77. The top one I think came off a 79. Yours definitely has been modified by somebody.

I believe bottom is from an A/C FJ40........................
 
Back
Top Bottom