Parting Out 1972 Toyota FJ40 LandCruiser

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

LCCRUISER

LCCRUISER

10 Year 15 Year
Joined
Mar 23, 2006
Threads
23
Messages
1,346
Location
N' HAMPSHA
Location
United States

Nice pic.

I need a few things:

Accelerator cable from the pedal to the carb (not the pedal but the firewall mount) 21,4, 21, 32


Heater valve 010


Rubber heater duct:


Cowl vent rod and knob 76 and 77



Let me know if you have any or all of those. Thanks
 
I have posted many pix of the vehicle if you look at the CL ad.
 
Thanks! Why didn't I think of that?

Plus there is the CL ad showing some parts and prices. PARTING OUT 1972 FJ40 LANDCRUISER FJ 40 LAND CRUISER PARTS

It's only been in the 30's recently so I haven't added more parts to my CL ad. I will pull parts for folks who want them if they are still available and when it gets a bit warmer. I can work at 40 degrees if its sunny, but not when it is colder than that or overcast or worse.

Thanks for your patience!
 
Bumper gussets

I could really use the bumper gussets from the sides and top of the front bumper there are 4 pieces total. let me know if you have them and what you want for them. I am in s.fl zip 34994
 
One is rotted and they both have a plow frame welded to the top of them.
 
F Engine Exhaust manifold

I could use an Exhaust Manifold or exhaust with the intake as a pair for my March 1972 FJ40 with F engine. My exhaust manifold has a hairline crack in it and is missing one of the bolt tabs. I'm interested in buying one of the un-cracked variety. Located in east Tennessee.
 
My steering wheel has a big split in the plastic on the hub. Maybe they all split. If yours in in good shape I could use it, also the turn signal assembly, mine is all there but the lever is broken off at the housing. I see that yous has the same wheel & signal switch in one of the pictures.
Thanks.
 
Are you willing to sell a part off the carb? I don't need the whole thing. I just need the bracket under the diaphram with the spring attached to it in pic 19 in your album.

Thanks
 
Exhaust Manifold picture

My exhaust manifold is cracked near the inside elbow of the #4 exhaust port near the intake manifold heat riser flange. This does not leak but my guess is it is all the way through. I expect any cracks would either begin inside an elbow or at the bolt tabs from being over tightened. I want the intake & exhaust if they have no obvious cracks.
Thanks
exhaust cracked near intake flange.webp
 
Cleg said:
My steering wheel has a big split in the plastic on the hub. Maybe they all split. If yours in in good shape I could use it, also the turn signal assembly, mine is all there but the lever is broken off at the housing. I see that yous has the same wheel & signal switch in one of the pictures.
Thanks.
Click to expand...

PM me so I can put you into my log there. Steering wheel is good. Someone has spoken for the turn signal assembly via a PM. They get first refusal unless it was you. It will be another couple weeks or so before I pull the wheel since i have to be able to steer it toward the trailer to scrap it.
 
Cleg said:
My exhaust manifold is cracked near the inside elbow of the #4 exhaust port near the intake manifold heat riser flange. This does not leak but my guess is it is all the way through. I expect any cracks would either begin inside an elbow or at the bolt tabs from being over tightened. I want the intake & exhaust if they have no obvious cracks.
Thanks
Click to expand...

Some of my bolts were barely finger tight and the rest were barely torqued. Now I know why it ran so poorly at the end, it was sucking air past the gasket. The good thing is that there might have been less stress on the manifold from not being tight and not cracked.

I'll get you some pix.

I would prefer to send parcel post or fedex ground if that is OK.
 
Millardo said:
Looking for a factory windshield washer bottle for my 3/72 FJ40. What condition is yours? Is the motor functional?

Thanks in advance!
Click to expand...

Info is in my CL link. Thanks.
 
Tireguy87 said:
Are you willing to sell a part off the carb? I don't need the whole thing. I just need the bracket under the diaphram with the spring attached to it in pic 19 in your album.

Thanks
Click to expand...

Nope!
 
parts

would you be willing to cut me out ths stock gas door area, im adding a second tank to mine and it would be cool to have anothe factory filler neck hole to put on it, if thats something you would do please get ahold of me, thank you
 
You must log in or register to reply here.

Share this page

Back
Top Bottom