Recent content by stereww

  1. S

    Toyota EPC Zip File Supply

    Looking for someone willing to provide me a download for the Toyota EPC desktop software in my DM? I've can't find one that works anywhere else on the internet. Thanks for your help in advance.
  2. S

    FZJ80 Audi Seat Retrofit

    Did you do anything special with the seat heat wiring? Additional resistors? I assume you left out the original temperature sensors in your setup?
  3. S

    Does a Lift Actually Increase Tire Clearance Without Bump Stop Modification?

    I can't speak to Bilsteins on the FZJ80. I have 5100s on my 97 4Runner. I assume you are talking about the 5100s here as I believe they are the only ones Bilstein sells for these trucks that are also designed for a lift. You may have read already, but they are stiffer than stock so that might...
  4. S

    FZJ80 Audi Seat Retrofit

    I think I have seen a couple people pull this off on the forums here, but I thought I would share my experience and pictures. My front and middle seats were destroyed when I bought the truck and I knew I wanted to replace them. Aftermarket options are expensive and/or limited. Same story with...
  5. S

    Does a Lift Actually Increase Tire Clearance Without Bump Stop Modification?

    Update for all. I got the rig out with 35x10.5x17 tires and FJ steelies at +15mm offset. So far is is working exactly as I had hoped. I have some pretty steep off camber mounds at the property and got it at a good angle in some places front and rear and full lock. So far I haven't heard any...
  6. S

    Wanted OME 861 and/or OME 862

    I figure someone might have a set of these laying around that they upgraded from. I would be interested in purchasing. Shipping would be to KC, MO.
  7. S

    Does a Lift Actually Increase Tire Clearance Without Bump Stop Modification?

    It's getting a new suspension no matter what since the springs are sagging pretty good and the shocks are looking tired. I think you are right, I will need to do some testing. I believe 30mm coil spacers would only provide additional tire clearance at straight and level. Once articulated, it...
  8. S

    Does a Lift Actually Increase Tire Clearance Without Bump Stop Modification?

    Unfortunately I could not find detailed dimensions for Ironman. Based on the 2" lift numbers I would be worried that the shocks designed for the 4" lift are bottoming out prior to hitting the bumps. I guess if you are hitting inner fenders the body has become the bumps, which I might be okay...
  9. S

    Does a Lift Actually Increase Tire Clearance Without Bump Stop Modification?

    I quickly scrolled through some of you build thread. Are you still on the 2.5" OMEs? How far did you extend your bumps?
  10. S

    Does a Lift Actually Increase Tire Clearance Without Bump Stop Modification?

    I'm doing a revival on a 1997 LX 450, drivetrain is complete and I am on to suspension and tires. I have gone fenderless and am wanting to avoid the tires sticking out past the body. My 1997 4Runner's tires poke out and it's always dirty. My solution is Kenda Klever R/T 35x10.5x17 tires and FJ...
  11. S

    Swapping a 1GZ-FE V12 into an 80 Series LC (FSM/EWD Help Request)

    Dream isn't dead, but it is on hold. Work has me potentially relocating to a remote area this spring, so we got to get the cruiser driving again. A new 1FZ is going back in it for now. Understandably, the service manuals are hard to come by. I might even be willing to roll the dice on a Japanese...
  12. S

    LX 570 Electrical System Can't Meet Demands

    Hi all, purchased a 2010 LX 570 a couple months ago. Higher mileage at 220,000, very well kept and low rust rig from the south. A couple weeks ago we had the infotainment black out on us cruising down the highway. It happened at least three times in a couple minutes. I noticed the voltage...
  13. S

    Swapping a 1GZ-FE V12 into an 80 Series LC (FSM/EWD Help Request)

    Drivetrain is out and ready for the V12. Unfortunately, my New Zealand contact who claims to have got a couple running on the floor has not answered my emails. Still looking for a Japanese contact to help out.
  14. S

    Swapping a 1GZ-FE V12 into an 80 Series LC (FSM/EWD Help Request)

    I have watched the skid factory's whole series. That one was a twin turbo, so they definitely used an aftermarket ECU. I have all the 80 series LC documentation (available on the documents page of the forum here for others looking) so that will be helpful, appreciate your offer. The imported...
  15. S

    Swapping a 1GZ-FE V12 into an 80 Series LC (FSM/EWD Help Request)

    I'll cut to chase and start with my need/request first. Below I will also summarize my pending plans for those interested, as I'm sure the title will bring some questions. I am looking at swapping a 1GZ-FE V12 from a 2nd gen Toyota Century (GZG50) into an 80 series. I need someone who has more...
Back
Top Bottom