Recent content by Snow Wagon

I too messaged TheForger and got no response about his tool. Harbor Freight carries the Pittsburgh Bolt-Type Wheel Puller Set. The bracket inside is the right size and the set is cheap (under $20). You need the bracket, (2) M10 x 50mm bolts, (2) M10 washers, (2) M10 nuts, (1) M8x1.25 x 40mm...

I realize this is an old post, but did the King Springs get sold?

Hello packeted, If they haven't been sold, and if you're willing to ship, I'd like to purchase them. I'm getting ready to do a HID upgrade and these look to be better than mine currently are. Thank you. Tom

Hello All, I've been in contact with someone that's done this. To do it right, you need the following: - Lower D Pillar Reinforcement (this is available separately and bolts in) - Upper D Pillar Reinforcement (this is NOT available separately and is welded into the D Pillar by the factory) -...

Not helpful. This discussion is about OEM, not Aftermarket. And it DOESN'T fit a LX470. If I was going Aftermarket, the Trail Tailor Spare Tire Carrier fits both the LX and LC, looks better built, and is made by someone that supports this website.

Has anyone done this install using the Factory Reinforcement Panel / Part? Part Number 61033-60100. If so, does this Reinforcement just bolt in from the Inside? If so, is it as easy as taking the trim off the inside, bolting it into place, then reinstalling the trim? Just want to make sure...

Hello All, Thank you hoser, suprarx7nut, and others for your responses and good info. Both the GX Basecamp and ADGU platforms are really good options, but I need something that's going to easily break down to be as flat as possible (storage / space is at a premium in the condo...). If I didn't...

Time to bring this thread back to life... I've read through the entire thread a few times, but my needs are a little different. My build is all about a temporary sleeping platform for 2 people (5' 10" and 5' 2"). I'd like something that can relatively easily be taken in and out, and I'd like to...

Yes. I know this is an old thread. But I can't seem to find the info anywhere on MUD, so... Based on reviewing A LOT of photos online, I believe these are different OEM / Factory Roof Rack configurations for both 100 Series Land Cruisers and Lexus LX470s. This should help someone buying a...

Hello Forum, So my 2007 GX470 w/ 90k miles was off the road for 8 months... I had to replace a broken (rusted...) brake line that ran above the gas tank. Brake line has been replaced, brakes bled, gas tank reinstalled, and now it's time to restart the SUV. Note: I consider this a very well...

There are some options on eBay for center cap stickers. The recessed area on the center cap is a little over 2 1/4”. So, you need a center cap sticker that size or smaller. 56 mm = 2.2 inches which is less than 2.25 inches :)...

I just picked up a set of the older style 5 spoke Tundra alloys. That's what I already have on the LX, and I guess they'll do for now... 1 set for winter, 1 set for the rest of the year. Thank you. Tom

Bummer. I'm in Pittsburgh, but my LX is in Denver. If you were local, I could take them "free" on my next Southwest flight to Denver. Shipping is rather cost prohibitive... I'll consider, but I'm leaning towards a set of Tundra alloys if I can't find a set of these in Denver.

Where in Ohio are you located?

https://atlanta.craigslist.org/atl/wto/d/atlanta-toyota-land-cruiser-wheels-and/7187508236.html Optional OEM 17” Land Cruiser Wheels. Dealer / Factory option from 2003 to 2007. Not Mine. If they were closer to Denver, I would buy them! Enjoy. Tom