Recent content by shakeandpop

  1. S

    Does this sound like a blend door issue?

    Seconding what excessive said above. If your cabin temp sensor is unplugged you will only get full hot, unless you put it all the way to max cold then it will blow cold air.
  2. S

    ARB Base Rack photos

    Long term ownership thoughts and opinions on the base rack? How are the 100 series owners liking this rack option? I noticed on their website arb now shows side rails and a 3/4 length basket option. I’d not seen this earlier when looking at their site. Anyone running either of these options and...
  3. S

    Tips on installing rear quarter window weather seal

    I replaced this seal on my truck for both sides. There was no sealant that I remember, neither on the original I removed or the new original I installed.
  4. S

    Partsouq - Exhaust Purchase ?

    Unlike the majority in this thread, my exhaust parts were NOT packaged very thoughtfully. However it all worked out fine and my new oem exhaust has been just fine.
  5. S

    Partsouq - Exhaust Purchase ?

    I purchased full exhaust from them, with no issues. You save significantly. I say go for it!
  6. S

    LRA 40 Gallon Replacement Tank Install

    87warrior, thanks for this great diy guide. Can you go into a little more detail as to extending the fuel suction and fuel return hoses that terminate at the top of the tank? For the fuel suction tube extension, did you cut into the hard nylon tube to separate both end couplers? Then simply...
  7. S

    Radiator 2nd choice

    For a land cruiser forum that worships oem Toyota parts there sure is a lot of discussion here about aftermarket radiators… I recently replaced my radiator with a Toyota one. Made by Toyo, Japan stamped, complete with foam and perfect drop in fit.
  8. S

    Need help: Body mount

    Also to remove #6, for the second mount I was able to remove with a simple swivel socket and small extension. 1/4” ratchet necessary because space was tight. You can do that or just hack bottom off with a jigsaw to create more space ha!!
  9. S

    Need help: Body mount

    sure thing - should’ve updated this post when I got it sorted. Reason I wasn’t able to get sufficient separation between chassis and frame to remove rear most body mount - is because I didn’t realize there are two additional bolts, accessed from within the truck, which were keeping chassis and...
  10. S

    Best replacement radiator for the money today...

    So I just installed a new oem radiator. Went with pn 16400-50360 for my 2002 truck. Was pleasantly surprised to see the radiator stamped “Japan” when I opened box to inspect. With all the talk of a Mexican spec oem radiator I assumed the radiator would be made in Mexico?? Either way fit was...
  11. S

    Steering knuckle corrosion- ok to reinstall or need new?

    I am in the middle of big steering knuckle / wheel bearing refresh. This is first time I’ve pulled the hub and examined the knuckle for myself. Am installing new oem CV’s, along with new bearings and hardware. Overkill but hey that’s how I do. After removing and cleaning up knuckle I’ve...
  12. S

    Best replacement radiator for the money today...

    Just replaced my fan clutch and shroud. While in there took notice of lots of dried coolant all along the top of the radiator where metal meets plastic. So needless to say looks like I’m in for a replacement radiator. My question is the distinction between these two OEM pn’s 16400-50360...
  13. S

    Center Console - Lid Snapped Off

    I replaced this recently. My hinge wasn’t completely snapped off but one of the arms had been compromised so there was a bit of a wobble in my armrest especially in its open state. The job was much more involved than I expected to simply replace the hinge. I had to disassemble pretty much the...
  14. S

    Remove lower control arm on-frame No. 2 Bushing: dimensions and parts to do it are attached

    Pressure has been checked and is good. Have swapped wheels left to right and back to front. Aligned multiple times on hunter machine. One thing that improved but did not completely solve pull was swap in completely new wheel/tire combo. Was a noticeable improvement from which I can only...
  15. S

    Remove lower control arm on-frame No. 2 Bushing: dimensions and parts to do it are attached

    I've been chasing a pull to the right in my 2002. Have had it aligned several times and have been told repeatedly it is in spec. New UCA and LCA, all new front end suspension really, new steering rack. Pull to the right manifested after a shop installed my UCA and LCA. If the spacer wasn't used...
Back
Top Bottom