Recent content by powderpig

I found the Mechanic page in the 60 section. I put them in Touch with Tyler Bussey shop in Delaware. Thanks for looking

Good day: A Young Couple that bought a Cruiser I worked on needs help with Diesel Cruiser. Anyone knows If there is a shop in or close to Toledo that can help. call me 303-884-7813 Thanks, Robbie

This is new, Keep in bag, on shelf over the years. Discontinued part by Toyota. $950 Plus Shipping to you, unless you happen to be near the area. Thanks for looking threezerothree eight84 seven81three call or text. thanks for looking

Engine alone is worth that

Sorry had to deal with some stuff. Not paying much attention to this. I still have my 93 80 with the same paint scheme that I have wheeled since 2001? 24 years, hard to part with. These days, I use a 2016 Ram 3500 with a hard side camper to 2 track, too many injury's to camp on the dirt any...

Thanks for your Opinion FJBEN. that a great review. While I am a bit busy to look at the Vehicles you are looking at. I may need to. When I priced this way back in June, I was looking at only a few VX's in the states. None had services work, pretty fresh in from Japan, no accessories and similar...

OK, I get it, a bit of bent metal. I can get it repaired or not. If Iget the Body repaired, what would it sell for them? $40K+? Keep the paint the same, or switch. While my Gas 80 series has been rocking this paint scheme since 94, I have been in it for 25years. Sort of has grown on me. Kid...

I have a Cruiser for sale. As listed this cruiser is a Japanese HD81 right hand drive with a newly rebuilt 1HD-T. 178,xxx KM or aprox 112,xxx miles on the whole vehicle. Clean Pennsylvania Title. Located in Rio Verde Foot hills, Arizona In the rebuild I had the fuel injection system rebuilt...

Thanks to the 283 people that have looked at this ad. I did have one person contact me. No deal struck. Will be moving this to main IH8MUD sale seciton.

I have a Cruiser for sale. As listed this cruiser is a Japanese HD81 with a newly rebuilt 1HD-T. 178,xxx KM or aprox 112,xxx miles on the whole vehicle. Clean Pennsylvania Title. tyring to sell local first. In the rebuild I had the fuel injection system rebuilt. The Turbo was rebuilt, but...

The Febest one is the one that was way off, like 30-40 degree. Messed me up for a few hr on a new build trying to figure out the issue. One hates to pull the fan shroud, fan an take a pulley after installing on a stand. What the customer wanted.

The thing I see that jumps out the most, is you have no sealing between the Fan shroud and the Radiator. So, Even when your fan engages, it is pulling hot air from the engine bay, and not thru the Radiator. The Radiator is only recieving air thru it from the speed of the cruiser thru the air...

Wow, Regular wheel bearing grease for Disc breaks will do just fine. the problem I have with synthetic is the Heat it take to flow the grease. Best recommendaiton I seen so far is the red and tacky. With conventional greases, the grease starts to flow at a lower temp, thus cleaning the bearing...

Decided to look thru the forums a bit more. Found this old thread. Cool. Ram 3500 is what Toyota should of built for us here in the US. Remeber in 2007 the Hino powered 2 wheel drive 1 ton they were pusing to events around thge country??. We could only dream then . I got a 2016 Cummins HO with...

Dr Gill Not even Toyota Pistons and Rings in that receipt. Hasting Rings are the worst for your block. Toyota pistons will set you back about 120 each(before the Tarriffs), Toyota ring set is going to set you back about 425. If they sold you Toyota Rods, main and thrust bearings might of...