Recent content by NC40

  1. N

    Help needed to identify drive flanges

    So regardless of the year of the FJA 80 axle you can use the hubs from a FJ 60 or Toyota truck?. I was under the impression that the year model of the 80 axle would determine whether or not you could use those hubs?
  2. N

    Help needed to identify drive flanges

    I am planning to use a set of FJ80 axles in my 69 FJ40 which has a FJ60 transmission and t-case. The t-case is part time and I do not want my front drive shaft turning unless I am wheeling, therefore I am looking to put a set of locking hubs on the front axle. Any help would be appreciated, thanks.
  3. N

    Manuel locking hubs

    I know you said no need to dismantle but they were already apart. I hope these are the pics you need.
  4. N

    Manuel locking hubs

    Thanks for the link. I am not sure what year model the 80 axles are. Is there a way to tell without dismantaling the axle?
  5. N

    Manuel locking hubs

    I am interested in the manual hubs for an 80 series axle as well, but for different reasons. My 80 axle is under my fj40 and I would like to have the locking hubs to keep the driveshaft from turning all the time. Is this a bolt on process or is there more to it than that?
  6. N

    For Sale Fj40 3/16 body armor

    Ok, wouldnt be suprised if it was $150 to get them to nc. Thanks man, I will check with fastenal.
  7. N

    For Sale Fj40 3/16 body armor

    Sorry, just read the initial post, I see now you are in cali.
  8. N

    For Sale Fj40 3/16 body armor

    Barn find where are you located? I too may be interested in a non cut set, especially if you are somewhat close to me.
  9. N

    FJ80 Rear axel in FJ40.

    Thanks for the info, that will essentially be the exact same setup as what i plan to do except your driveshaft is longer than mine will be. Are you running a toyota dc shaft or a custom shaft like a tom woods?
  10. N

    FJ80 Rear axel in FJ40.

    Thanks white stripe, that is more less what i need to know. Roc Doc stated earlier that it would not matter if I ran compound angles as long as I had a NON DC shaft. So it would be better to run a standard shaft with that setup vs a double cardan/cv style?
  11. N

    FJ80 Rear axel in FJ40.

    I understand that the front axle is 4" wider on each side, and i am prepared to make whatever bracketry needed to hang the axle. The front drive shaft wont be turning at high speeds like the rear shaft. Also the front differential in an 80 has the same offset as a fj40 axle which means it will...
  12. N

    FJ80 Rear axel in FJ40.

    Gotcha. I just didnt know how critical the driveshaft angles would be if there was an offset horizontally on a vehicle that is driven at 60 mph regularly.
  13. N

    FJ80 Rear axel in FJ40.

    Good to know! I read earlier that the 80 axle is 4" offset from center and the fj60/40 axle is 6" from center, is that right? If so, i thought I could push the axle over 2" towards the passenger side as long as I put a 2" spacer on the drivers side wheel, and also a 1" spacer on both sides of...
  14. N

    FJ80 Rear axel in FJ40.

    New member here, my apologies ahead of time if this is not the correct place for this question, but I was wondering about a somewhat similar situation I have. I am looking to swap a set of fj80 axles into my 40 which has a stock trans and tcase from a fj60. I know the front axle will work fine...
Back
Top Bottom