Help needed to identify drive flanges

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 1, 2016
Threads
1
Messages
14
Location
Central NC
I am planning to use a set of FJ80 axles in my 69 FJ40 which has a FJ60 transmission and t-case. The t-case is part time and I do not want my front drive shaft turning unless I am wheeling, therefore I am looking to put a set of locking hubs on the front axle. Any help would be appreciated, thanks.
image.webp

image.webp

image.webp
 
You can run Aisin hubs from a FJ60 or Toyota truck. The 80 wheel hub has the cutouts that make it look weird but the listed locking hubs work fine. Only downfall is not being able to drill for more dowels.
 
So regardless of the year of the FJA 80 axle you can use the hubs from a FJ 60 or Toyota truck?. I was under the impression that the year model of the 80 axle would determine whether or not you could use those hubs?
 
nothing wrong with running drive flanges, my 82 fj40 did 130,000K(than put Aisin on) with the set it came with from Japan
 
nothing wrong with running drive flanges, my 82 fj40 did 130,000K(than put Aisin on) with the set it came with from Japan

I respectfully disagree. Considering the nuisance of replacing birfield seals, I'd rather not be spinning axleshafts unless I'm wheeling.

Best

Mark
 
Don't over think this, the hubs fit the earlier 80 Birfs no mods needed, if your running the latter bifs (longer by a bit) re groove the stub to run the snap ring (the dial will clear the longer stub without any modification ) or don't run the outters snap ring at all.

I have put several of these together and this works.

I agree with @65swb45 Mark on not turring that mass if it's not necessary.
 
nothing wrong with running drive flanges, my 82 fj40 did 130,000K(than put Aisin on) with the set it came with from Japan
I recently purchased an "80" FJ40 (136,000 miles) with drive flanges. Comments from posters here on MUD have made me park it until I install a set of Aisin hubs. Can I drive it on asphalt at least to have it inspected and a muffler installed? Thanks. Is there any other peculiarities about the transfer case, front or rear differentials I should know about? Thanks
 
I recently purchased an "80" FJ40 (136,000 miles) with drive flanges. Comments from posters here on MUD have made me park it until I install a set of Aisin hubs. Can I drive it on asphalt at least to have it inspected and a muffler installed? Thanks. Is there any other peculiarities about the transfer case, front or rear differentials I should know about? Thanks

Feel free to drive it anywhere you like. Just make sure you're in 2wd, and you won't damage a thing. You're just putting unnecessary wear on the front end components with the drive flanges. I do find it very strange that you have drive flanges on a 1980 FJ40, as it should have come with locking hubs from the factory in the US market.
 
Last edited:
Feel free to drive it anywhere you like. Just make sure you're in 2wd, and you won't damage a thing. You're just putting unnecessary wear on the front end components with the drive flanges. I do find it very strange that you have drive flanges on a 1980 FJ40, as it should have come with locking hubs from the factory in the US market.
May 1980 production date. Some of the data plate info I can't find reference to even in the FAQ section.
 
In the US market, FJ40s started shipping with the lock out hubs in the 79 model year. My May 79 has them; FJ55s were shipping with them for years earlier, my 78 FJ55 has them, along with the stock long birfs. Your truck should definitely have shipped with the locking hubs in the US. So either a PO swapped them out, or perhaps your entire axle was swapped. Are your birfs the early long, or later short?
 
Last edited:
In the US market, FJ40s started shipping with the lock out hubs in the 79 model year. My May 79 has them; FJ55s were shipping with them for years earlier, my 78 FJ55 has them, along with the stock long birfs. Your truck should definitely have shipped with the locking hubs in the US.
...hmmmm. Makes me wonder why and if there are any surprises awaiting me when I go to install locking hubs.
 
In the US market, FJ40s started shipping with the lock out hubs in the 79 model year. My May 79 has them; FJ55s were shipping with them for years earlier, my 78 FJ55 has them, along with the stock long birfs. Your truck should definitely have shipped with the locking hubs in the US. So either a PO swapped them out, or perhaps your entire axle was swapped. Are your birfs the early long, or later short?
Axle info on the data plate reads "K052" then in black letters 0-12
 
The data plate means nothing. A PO could have swapped an entire axle, differential, gears, or various parts on you. You need to determine if you have the early long birfs, or the later short birfs. If you have the later short birfs; good news, as those locking hubs are readily available. If you have the early long birfs, I would swap them out for the newer shorts, which are what your truck should have anyway. "birf" = birfield joint. Do a quick search here to see pictures. Or give me a minute, and I'll give you a link.
 
The data plate means nothing. A PO could have swapped an entire axle, differential, gears, or various parts on you. You need to determine if you have the early long birfs, or the later short birfs. If you have the later short birfs; good news, as those locking hubs are readily available. If you have the early long birfs, I would swap them out for the newer shorts, which are what your truck should have anyway. "birf" = birfield joint. Do a quick search here to see pictures. Or give me a minute, and I'll give you a link.
 
my US spec 82 FJ40 still had the drive plates on it when I found it in 2003, one adult owner(who worked for Lockeed as an engineer) nothing ever changed. so yes, they still had drive plates. I think the locking hubs were port installed or dealer installed and some may have come from Japan with AISIN's

332254121.jpg
[/IMG]
332254121.jpg


In the US market, FJ40s started shipping with the lock out hubs in the 79 model year. My May 79 has them; FJ55s were shipping with them for years earlier, my 78 FJ55 has them, along with the stock long birfs. Your truck should definitely have shipped with the locking hubs in the US. So either a PO swapped them out, or perhaps your entire axle was swapped. Are your birfs the early long, or later short?
 
Back
Top Bottom