Recent content by Mapster

  1. M

    Harmonic Balancer wobbly?

    Maybe I need a new HB from CDAN. I'll take a video later today and post it. Thanks
  2. M

    Harmonic Balancer wobbly?

    Apologies for the confusion. I was referring to the rubber seal, not the Harmonic Balancer. I was doing a project to get rid of the oil leaks - O-ring on the dizzy, O-ring on the oil pump cover and the rubber seal on the crank pully. Thanks
  3. M

    Harmonic Balancer wobbly?

    How can it fail when I just replaced it with a brand new one from CDAN? Thanks
  4. M

    Harmonic Balancer wobbly?

    Today, I started up my baby and noticed the harmonic balancer was running straight. No wobbly effect at all, when it's cold and the RPM is running high as the engine is getting warm. After it warmed up and at normal idle, it started to wobble. Any ideas as to why? Thanks
  5. M

    Crank Pulley Bolt Torque Question

    I 2nd the fatty pipe. Go to Home Depot. I think, it's 1 1/2" calvanized pipe and couplers. I used 3 of each, once connected, it's quite a cheater bar, to go over the HF torque wrench.
  6. M

    Harmonic Balancer wobbly?

    That's the same one I used, with 3 calvanize tubing & 3 couplers from Home Depot. So much easier using that as a cheater bar. First, I set the torque wrench to 300 lbs. Click. Then set it to 304 lbs. Click.
  7. M

    Harmonic Balancer wobbly?

    Wobbly enough for me to see it, looking straight down from top of the radiator. No, it wasn't like that before I removed the crank pulley and did not drop it. In fact, I was very careful with it per Texasknowhow video. I'll try the belt today and check again. Thanks
  8. M

    Harmonic Balancer wobbly?

    I read on another post to try tightening the belts. I'll try that tomorrow and see if it works. If not, I'll have to remove the crank pulley and check the sealer if it's seated, correctly. Thanks
  9. M

    Harmonic Balancer wobbly?

    I followed Texasknowhow video to remove the bolt, then, removed the balancer with my hands. Installed the new plastic seal from CDAN, again, following Texasknowhow how-to, by using a plastic coupler. Maybe, the plastic sealer wasn't seated correctly but I thought I checked it before...
  10. M

    P0401 Cause by EGR Wiring?

    94 LC LC died on the road. Found out the EGR wiring burned since it was sitting on top of the valve cover. Had a Ih8MUD member fixed the wiring. Now I get the P0401 CEL. Before I check for the P0401, would the wiring fix cause the P0401? Thanks
  11. M

    Harmonic Balancer wobbly?

    94 Land Cruiser Just did the oil fix on the dizzy, oil pump cover and harmonic balancer. Used a 300 lbs torque wrench from Harbors Freight with cheater bar to crank to 300 lbs. Then, at 304 lbs, even though the torque wrench is rated at 300lbs. Anyway, after putting everything back, the...
  12. M

    40, 60, 70, 80, & 200 Series Cup Holders

    Please, let me know when you'll have the rear double cupholders. Thanks
  13. M

    Toyota Red dries up inside Radiator?

    Out in the open? After draining the Toyota Red coolant, I removed the inlet hose (top) along with the small hose near it and coolant reservoir. So those 3 hoses were left open for a week during the summer before I put painter's tape on it. That's how it was left open. Thanks
  14. M

    Toyota Red dries up inside Radiator?

    Yes. Putting back Toyota Red. I wonder if any leftover dried up Toyota Red in the radiator (after flushing it) will dissolve once the engine is at normal temperature?
  15. M

    Toyota Red dries up inside Radiator?

    94 FJZ80 radiator question. Back in July, I drained the coolant to replace a a leaking hose by the firewall (not the PHH) and did not complete the process due to health issues. I did not flush out the radiator with water at all so my question is: Will traces of Toyota Red inside the radiator...
Back
Top Bottom