Recent content by Jarrat

  1. Jarrat

    Landcruiser Series Brake Bracket Bell Crank for parking brake LH and RH

    Hey guys, I just saw these messages now, I do have 1 set I could mail off, anyone need a set, I could make more. Message me, so I can get an idea, I'll post them up forsale on Ebay once I get a bunch going and remove these messages of this thread.
  2. Jarrat

    Color codes

    Any chance does anyone know how to get the color paint codes for the lj78 prados?
  3. Jarrat

    Landcruiser Series Brake Bracket Bell Crank for parking brake LH and RH

    Yes it does!!.. now I don't have crappy cast ones that could break again.
  4. Jarrat

    Landcruiser Series Brake Bracket Bell Crank for parking brake LH and RH

    I managed to find and pick up a factory rear axle with the factory locker for my 1990 LJ78. Taking it apart I noticed the brake bell cranks were both broken. I quickly looked up the part number (47629-60010) and (47628-60010) Left and right side. Found a person on EBAY selling them (search...
  5. Jarrat

    Overcoming 2LTE fuel cut limit

    Still haven't done it yet... been spending my free time on my little honda crx so I can drive that next week.. soon as Ive got it Ill let you know!!
  6. Jarrat

    Overcoming 2LTE fuel cut limit

    Sweet... Im doing that tonight!!
  7. Jarrat

    Build My LJ78 build thread...

    Now I needed the factory side to seal against the snorkel a bit better so I did this. Also had to cut this up.. and while I was doing this... I swapped out this part for a new one. and when I was done, it looked like this!!!!
  8. Jarrat

    Build My LJ78 build thread...

    Now I needed something from the air box to the snorkel, or else it wasn't doing anything. So I drew up a part in solid works and printed it up on my printer. It took 2 tries of 10 hours of printing until I got it right. I had to heat up the other end and bend it into its spot so I...
  9. Jarrat

    Build My LJ78 build thread...

    Once I had all the rivet nuts figured out I started on the large hole. Here is my mock up Now after cutting. and this is what the factory part looks like.
  10. Jarrat

    Build My LJ78 build thread...

    Now for the fun part, I installed a factory Landcruiser snorkel. I'm pretty sure this snorkel wasn't meant for this truck and I knew it would need a custom part to make it work, but I was up for the challenge. Thats all I got, I had to borrow a thread rivet tool and 3d print my custom part...
  11. Jarrat

    Build My LJ78 build thread...

    I also replaced this bushing.... I forgot the part number. I'd recommend replacing this every few years as it affect handling a lot.
  12. Jarrat

    Build My LJ78 build thread...

    Lets talk about turbos...... I've finally bought a new turbo, well not a new new one, but a ebay core. Got some good feed back from a couple different people about these ebay cores lasting, and so far so good! My old one was DEAD.... this pic was from JUST 1 week of driving after draining...
  13. Jarrat

    Build My LJ78 build thread...

    My down pipe cracked and I re did my rusted out muffler. I need to redo it all over again, because now my flange isn't sealing properly to the turbo and my muffler is hanging down to low. Here are some pics. Pics of the crack. and here is my attempt at fixing it.... letting it cool very...
  14. Jarrat

    Build My LJ78 build thread...

    I ended up doing all my tie rods and relay links a few month back also... I pieced together toyota ones from ebay for 3 of them, and another "555" brand which I found out afterwards makes a whole replacement kit for waaaaaaaay cheaper then what I spent. Here are the part numbers in case you...
  15. Jarrat

    Build My LJ78 build thread...

    Ok, more updates, I need to update about boost, I'm pushing the max PSI (18-19psi )I can out of my turbo setup with the help of a air speed controller given to my by GTSSportCoupe and it has worked like a hot dam. Must say very impressed by how it works. I have my boost lines routed differently...
Back
Top Bottom