Recent content by jaredmcginness

  1. jaredmcginness

    '71 40 Refresh - First rodeo.

    Well, 40 was on the back burner, covered up, tucked away. Finished 3 customer Porsches and built this turn key ‘68 for myself. 99% done Moving into a new home next week and finally have a dedicated indoor spot for the 40. FINALLY title is on the way (I hope). ordered a windshield and...
  2. jaredmcginness

    Wanted WTB: early door pair. (Ideally freeborn red) (MD/DC/PA)

    Hey folks, Looking for a decent/nice pair of early doors. Freeborn red with patina but little to No rust would be great. Located in Baltimore. Willing to travel a bit if needed. Thanks!
  3. jaredmcginness

    Wanted Looking for a title off a 69-71 fj40. Anyone have one from a parted truck?

    I'll have to look into that. I havnt heard about either of these states doing that. VT closed down their generous title services in July. Americas DMV is closed. You now must have ties to the state to tag a vehicle there.
  4. jaredmcginness

    Wanted Looking for a title off a 69-71 fj40. Anyone have one from a parted truck?

    Hi all, In search of a "historic document" off of a fj40. I missed the Vermont DMV services window on the truck I am restoring and need to look into other options. Thanks!
  5. jaredmcginness

    '71 40 Refresh - First rodeo.

    I love the look! Pretty confident these are the only OE Porsche seats in a 40 .... sans maybe any Recaro LS or similar - which don't exactly count. I have to park her outside for a few weeks (while hopefully still squeezing in some work) to get a customer car inside. Next on the...
  6. jaredmcginness

    '71 40 Refresh - First rodeo.

    Hi guys, Made up some seat sliders for the drivers seat. Previously, the old (crappy) seat was held into the toolbox lid with 2 #12 self tappers. Real secure :P As such, the driver's seat sat about 3" lower than the passenger - which was basically flush to the .25" sliders on the gas tank...
  7. jaredmcginness

    '71 40 Refresh - First rodeo.

    Cut up some gasket material for the new seat sliders. Drilled the holes and added gaskets to the tail gate... The water jet at my work is down for the next 2 months, when repaired I will cut some cleaner looking seals up. Definitely a ton of progress. For a good comparison, here is the...
  8. jaredmcginness

    '71 40 Refresh - First rodeo.

    Last weekend I laid paint down on the car. I had a local shop auto paint color match 5 aerosol cans. Worked.... OK. It's a decent match, but doesnt look dead on like Freeborn. Kinda looks like s***, but I am also thrilled with how far it's come. I think a wet sand will help freshen it...
  9. jaredmcginness

    '71 40 Refresh - First rodeo.

    Welded the semi-repaired tool box back in. I also rolled up the cross arch that goes over the trans tunnel. Coated the new floor in primer so it could sit around for a week until i could get back to it. Started my least favorite part (Messy!) Base prime and block sanding. (I used a 2k...
  10. jaredmcginness

    '71 40 Refresh - First rodeo.

    Hey fellas, Tons of updates. Opened my tool box for the first time. Yikes. Lots of cool old replaced ignition bits in there. Cut the floor out, POR 15 the channels: Made a new floor out of some 16 gauge scrap I had laying around. Also, sheared up some .187 thick steel for a sturdy...
  11. jaredmcginness

    '71 40 Refresh - First rodeo.

    I have decided to use a spare set of buckets seats I had laying around. They are amazing and should fit well with the truck. These are mid 70's Porsche "Pascha" seats. Pattern used in the both 911 and 928. Here I am making up some 1/4" steel brackets for mounting of the passenger...
  12. jaredmcginness

    '71 40 Refresh - First rodeo.

    Scuffed First coat of raptor liner I know the transition for the bed to the to the rear sill is really ugly. I will be screwing down a stainless kick transition for that area. 3 Coats - definitely helps to hide the many imperfections.
  13. jaredmcginness

    '71 40 Refresh - First rodeo.

    Hey guys, Tons of updates. You don't feel like you make progress that's worth sharing on a day to day - but look back after 4 or 5 weeks and it starts to look like a lot! I feel a little bad about all this work, I am rushing through a lot of it. But a fix is a fix. Repairing the rust on...
Back
Top Bottom