Recent content by Dudemanslick

  1. D

    Timing Marks are correct, no power...

    So i adjusted the distributor to where its supposed to be, pics are attached. The truck runs and revs fine, but its falling on its face when I try and take off. The timing with a light in service mode is at 3°... Note: the rotor button was a tooth retard when I pulled the cap, I figured there...
  2. D

    1fz-fe Misfire/stumbles in when put into gear!

    I've got cash for time and There is a beer store about a block away 😌🤣 I've been trying to track down another ecu to just plug and play, no luck quite yet
  3. D

    1fz-fe Misfire/stumbles in when put into gear!

    Yes! I followed it Exactly! And no offense taken at all, i work on cara for a living, i own a customs shop north of bham , i stay wrenching lol. so quick back story, I did the headgasket back in November, drove the truck with no problems for a few months , then out of nowhere I started having a...
  4. D

    1fz-fe Misfire/stumbles in when put into gear!

    Update: I just set the distributor back a tooth, and it solved my stumble when I blip the gas but my timing light is showing my timing at about 30 or 40° off, when I turn the distributor counter the closest I can get is about 25° ....also...just put another set of brand new wires ans spark...
  5. D

    1fz-fe Misfire/stumbles in when put into gear!

    The amount of time between the piston stopping and going back down is long. Are you supposed to set the dizzy when the crank mark is at 3?
  6. D

    1fz-fe Misfire/stumbles in when put into gear!

    Here's what we got at tdc now
  7. D

    1fz-fe Misfire/stumbles in when put into gear!

    Yes I did pull it, so I just used the distributor to set it right at 3 with timing light, the idle lowered to about 1200..., you may be onto something, i followed the photos I found online to adjust the distributor, but like you said I may still be a tooth off
  8. D

    1fz-fe Misfire/stumbles in when put into gear!

    When i put the shifter into gear or reverse the idle is at 650-800...but with, what sounds like misfire..
  9. D

    1fz-fe Misfire/stumbles in when put into gear!

    I just bought a cheap one, maybe 60$ , im running out funds for this head scratcher..it made a noticeable difference...the idle is very smooth now, but it wont take throttle at a normal pace...if I let it stumble a second with my foot on the pedal it clears up...
  10. D

    1fz-fe Misfire/stumbles in when put into gear!

    Funny you asked about idle, it's sitting at about 1500rpm...but the cable is fully slacked...I can't get it any lower, also noted that with the ac on the idle does not change...i
  11. D

    1fz-fe Misfire/stumbles in when put into gear!

    Update : just replaced iacv, tps and EFI relay,not much change, the trucks runs great when the revs get past about 2k rpm...below that the truck is still struggling bad, sprayed ether around intake again but there are no leaks. If I attempt to blip the throttle, it's an immediate misfire..., but...
  12. D

    1fz-fe Misfire/stumbles in when put into gear!

    Yes , sorry im unsure, don't know too much about these trucks
  13. D

    1fz-fe Misfire/stumbles in when put into gear!

    Ive got the back 2, but the ones right off the engine have been blocked off, they never caused any issues other than stinky exhuast
  14. D

    1fz-fe Misfire/stumbles in when put into gear!

    Ok, so replaced the ignitor with a new one, the truck on cold start did not idle up past maybe 300 rpm.., then I noticed that the rpm gauge wasn't working...I think this is an ecu problem..., the ignitor made no change, and we checked all the vacuum lines again while re-installing the throttle...
  15. D

    1fz-fe Misfire/stumbles in when put into gear!

    Timing is what I think , DEAD ON, even grabbed a timing light , i think it's at 5°,and consistent now that I replaced the dizzy..
Back
Top Bottom