Recent content by Connorrw

  1. Connorrw

    Center Diff Locker Air Actuator Build

    My CDL locker actuator has been flaky and now no longer works. I tried troubleshooting and found that both the electric actuator is burned out and I have some wiring issue behind the dash. Seems like its pretty common to have the actuator fail, but with the combination of a wiring issue, I...
  2. Connorrw

    37s v 35s on OME 2.5 Suspension Analysis

    Thanks to all for the response. 35s it is. Also seems like there is some misconceptions on the scanning and time/effort and I think the process is pretty cool. Scanners are pretty amazing now. Scanning the rear of the truck took about 2 minutes and then bringing it into CAD and doing the...
  3. Connorrw

    37s v 35s on OME 2.5 Suspension Analysis

    Thanks Mark for the answer. I think even 2.5 inches of lift is too low for 35s but it was I have/am stuck with for a while. I chose it initially as I knew I wouldn't have any problems with driveline angles, major caster problems beyond what bushing could correct, etc. In light of that, my...
  4. Connorrw

    37s v 35s on OME 2.5 Suspension Analysis

    That is my concern, and my question is that in a lot of other posts, it is said that cutting is required for 37s to fit on a 2.5 inch lift. This doesn't seem to be strictly true? Flex is only limited by about a degree. Is that true, and do people have to cut? Is it not 37s can fit reasonably...
  5. Connorrw

    37s v 35s on OME 2.5 Suspension Analysis

    That's a good point. I considered that, but thought that angles would get weird and it would result in more of an impact than simply the tire radius. I don't see many people running 37s on the 2.5 inch lift but it seems like a fine decision with little impact. I was concerned on how the track...
  6. Connorrw

    37s v 35s on OME 2.5 Suspension Analysis

    Hello All, I'd like some opinions on some options I am considering. I currently have a FZJ80 with the basic OME 2.5 Inch lift running 35x12.5 tires. This has done well and let me do some great trails, but I am often scraping and am considering moving up to 37s. My principal concern was in...
  7. Connorrw

    Wanted Wanting P/S air vent and cover.

    As title says, looking to buy the air duct and cover plate in brown with wood trim for my FJ80. Pics showing more detail. Missing Part Color Reference.
  8. Connorrw

    97 FZJ80 CDL Issue

    Haven't figued out anything more. Shelved until trails close for the winter.
  9. Connorrw

    97 FZJ80 CDL Issue

    Hello All, I am here trying to get some help on a CDL issue I've been having after doing the 7th pin mod. I've found lots of similar threads, but nothing that describes what I am seeing. Background - I did the 7th pin mod following Slee's guide. I pulled a hazard switch out of a parts truck...
  10. Connorrw

    SOLD 1996/1997 80 Series or LX450

    Anything within a day's drive of Denver. Primary thing is rust free and in a state that it could drive home Denver. Budget is around 10k.
  11. Connorrw

    SOLD 1996/1997 FZJ80 or LX450

    Decided to pass on the 367k-mile truck. Still looking. I'll consider up to 10K trucks
  12. Connorrw

    SOLD 1996/1997 FZJ80 or LX450

    Title says it all. Hoping to buy a 1996/1997 FZJ80 or LX450, preferably within 500 miles of Denver. Budget is 8k. Really looking for rust free and in a state it could make it back to Denver. Found one for 6k but has 375k miles. Thoughts on that being too many?
  13. Connorrw

    FJ80 3FE Surging/No Power

    I scoped NE and G at the ECU. Below are the results. This was after checking the distributor gaps per IG-9. Img 1 - NE Img 2 - G Img 3 - IGF All were taken during the problem. I also went back to the code 41 TPS and recalibrated my TPS with the gauges. This may have made a difference as...
  14. Connorrw

    FJ80 3FE Surging/No Power

    After further testing, I wanted to verify that spark was reaching all cylinders. I put the timing light on individual plug wires and saw some hiccups. I then tested the plug wire from the coil to the distributor and saw the same hiccups. See below for the video. Its a little bit harder to see in...
  15. Connorrw

    FJ80 3FE Surging/No Power

    I verified with an oscilloscope on the ECU pin while the surging was occurring that the relay output was constant and that it wasn't triggering by feeling it while running. I then unplugged the sensors, trying to force the issue not to occur. At first, I unplugged: AFM TPS All...
Back
Top Bottom