Recent content by Bzerker999

  1. B

    Blown Engine 66 FJ40

    Damn, well thank for looking, I believe DOR has some used one?
  2. B

    Blown Engine 66 FJ40

    The one on the left looks exactly like mine, the shaft diameter is 0.274"(about 1/4") and about 11 3/8" long.
  3. B

    Blown Engine 66 FJ40

    I need to buy at least two push rods. I am having a problem with getting me phone's (very old and cheap) pictures into my computer. Will make another attempt today. is there any measurement I can take that will help?
  4. B

    Blown Engine 66 FJ40

    Head is off and everything looks good so I would like to purchase two puh rods from you. How do I pay you for them?
  5. B

    Blown Engine 66 FJ40

    Success - at least step 1, the head is off and I cannot see any damage to the valves, pistons nor cylinder wall. In fact everything looks very clean, very little carbon build up and no ring ridge. This engine has been rebuilt sometime in its past So all I need is two push rods and I will be able...
  6. B

    Blown Engine 66 FJ40

    My compression was good before this event and the oil pressure was good when I shut the engine off so I am hoping I do not need another engine. But having a spare would not be a bad idea.
  7. B

    Blown Engine 66 FJ40

    I finally got the intake/exhaust manifold off with out breaking any thing. The head will come off this afternoon. The intake ports on the head are round and I found the following numbers on the head: Front/top 51116 Rear/top 111 60020 32
  8. B

    Blown Engine 66 FJ40

    Thanks for the info I will get some pictures and post them this PM. Got the exhaust bolt to turn a quarter of a turn after one hour of messing with is, a work in progress. Thanks for the info, sounds like wha exactly happened to me.. Luckly I do have a spare head.
  9. B

    Blown Engine 66 FJ40

    Appreciate the offer. I am still in the investigation phase, hope to have the head off today, but the exhaust manifold is giving me fit but what is unusual about that I am confused, I see "135" mentioned is this what is in a stock 66 fj40?
  10. B

    Blown Engine 66 FJ40

    Appreciate it, I will need at least two that I know are bent. But first I am going to pull the head, already have it half of but found a problem with the exhaust manifold where it connects to the exhaust pipe, broken tab and frozen bolt, I am sure that will tke me more than a few hour to get...
  11. B

    Blown Engine 66 FJ40

    As I have more time than I have money I am going to pull the head. The main reason is that one of the push rods did not come completely off and was caught under the adjustment nut thereby opening the valve mush farther than they should be and that could be the slapping noise I heard. I also...
  12. B

    Blown Engine 66 FJ40

    Great Fall Montana
  13. B

    Blown Engine 66 FJ40

    I spent 2 hour searching for push rods and could not find a source, any suggestions?
  14. B

    Blown Engine 66 FJ40

    Got my rig in the shop and pulled the valve cover. Found two push rod that had become unseated and of course they are both bend. Do not know if the cam or the pistons are damaged. Next step is to pull the head and check the pistons and pull the side covers and check the cam. Not sure why or...
  15. B

    Blown Engine 66 FJ40

    I blew the bottom radiator hose and I lost water so fast i did not even see the temp rising. The engine started clattering and missing badly. Towed my rig to my shop Not knowing all that is wrong, I first replaced all radiator hoses, including heater hoses. Started engine and it still clattered...
Back
Top Bottom