Recent content by andyGX470

  1. andyGX470

    Build Zuninja's 2005 GX470 "Build"

    Got my kit from PartsGeek. 🤞🏼 Hopefully it holds out. It was Aisin though.
  2. andyGX470

    GX470 Frame Swap Project

    I was able to get the rig all buttoned up late last week. Just in time to drive take it on our yearly roadtrip. Currently ~1200 miles in with only one real issue (i'll discuss more below). I was a little worried about having a fitting leak on the various oil/coolant/ATF systems since all got...
  3. andyGX470

    GX470 Frame Swap Project

    On Sunday, the engine build up was completed and we got everything mounted onto the frame. The following components were replaced: Front main seal Oil pump Water pump kit Power steering pump AC condensor
  4. andyGX470

    GX470 Frame Swap Project

    Update: I was able to weld my exhaust manifolds. Hopefully this gives me a little bit more time to wait for GX470 headers to be developed / more widely available. Saturday, I was able to finish getting all the suspension components swapped over to the new chassis. I've added some blue paint...
  5. andyGX470

    GX470 Frame Swap Project

    First coat of primer on! All the tedious prep work is paying off. I was worried about thinning out the original mastercoat rust sealer primer but using a scale and just mixing in 10% of the thinner they sell by weight wasn’t bad at all. The paint gun I’m using is 1.8mm and it seems to come out...
  6. andyGX470

    GX470 Frame Swap Project

    I just ran out and checked and sure enough they are cracked. I'm so glad I checked. I wonder if I could just take these to a welder and have him run a bead inside and out for now. I don't think i'll have time to fab headers between now and July (scheduled road trip). See pictures below:
  7. andyGX470

    GX470 Frame Swap Project

    Its really not that bad. Probably a full Saturday if you leave the engine and trans attached to the frame.
  8. andyGX470

    GX470 Frame Swap Project

    This is super encouraging! Thanks, I was planning to try mounting the engine and trans before putting the body on. I Wasn't sure I could get enough clearance when I took it off but I think this confirms its possible. Doing so will definitely save me a bunch of time on reassembly! About the...
  9. andyGX470

    GX470 Frame Swap Project

    After many, many hours of grinding. I've finally gotten as much of the old paint off as I can. I've decided to just scuff and paint the non structural cross braces. Its nearly impossible to get a good angle on them with a grinder. Plus looking at the old frame they didn't rust after 20 years so...
  10. andyGX470

    GX470 Frame Swap Project

    I've begun the long slow process of paint prep. I'm starting by hitting the large sections with a 4.5" 50 grit sanding wheel on my grinder then will follow up with a 2" 90 degree die grinder to get the smaller pockets. It's slow but satisfying work -especially after a long day at the office...
  11. andyGX470

    GX470 Frame Swap Project

    I heard back from XAT… Here is what they said: “Hello, this is Lonnie from XAT Thanks for your order. Unfortunately these have been on backorder since at least Oct 2025, and the rumor is that Doug Thorley is discontinuing these as an option. There are none left nationwide as far as we can...
  12. andyGX470

    GX470 Frame Swap Project

    Thats a real bummer. I wonder why they discontinued them?
  13. andyGX470

    GX470 Frame Swap Project

    Successfully got the body and frame separated! This is totally doable without a lift!
  14. andyGX470

    GX470 Frame Swap Project

    Based on a little research i've decided to go with mastercoat as the paint supplier for the frame. They are currently out of stock but I plan to purchase the kit below or piece it together myself. https://nomorerust.com/products/mastercoat-complete-truck-chassis-kit
Back
Top Bottom