Which Lift?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 2, 2008
Threads
127
Messages
1,916
Location
San Diego
The first mod I'd like to do for my LX450 is a 2 to 3 inch lift. I live in SoCal and will be using this as a weekend warrior for camping and offroad exploring, no major rock crawling. Anza Borrego looks like the playground I will be exploring most and maybe some stuff up in BigBear. Anyway, from the searches I've done so far, the 2.5" OME w/mediums looks like it will be the best bang for the buck. Any other good options? Would be glad to hear some opinions before I make a final decision. Thanks in advance for your input.

Derrick
 
I purchased the Slee DIY 4" lift kit about a month ago. It was $2220.00 shipped to So Cal. So far I've got the front half completed.

I wish I could tell you more about the ride quality of it but it's not completed. Slee still has not shipped me the rear pan-hard adjusted yet. I'm not very pleased about the delay in parts. I'll be calling them in the morning to inquire about it again.

If I ever get this done ill give you more info.
 
I probably should have added that I am trying to keep the lift as minimal as possible to keep the vehicle family friendly for my wife and three kids. But I do want enough to make room for the 285/75R16 Nittos I have on it. jjdeneen918, I would still like to hear about your 4"DIY Slee. Post some pics when you are finished. Thanks!
 
Just remember that the more lift you add, the more mods you need and the more money it takes...

Not a lot of people get the stock height OME suspension, but I think this gives you about 1" of lift and doesn't require any additional mods. The people who have this report an improved ride and seem happy with it.

I considered that option, but I needed to tow and I wanted sliders and a front bumper. As a result, I ended up with OME mediums in the rear (860) and OME heavies in the front (850). This got me a 3" lift and I had to modify the LSVP, install the yellow caster kit, and I have slight vibrations over 75 mph.

I also hear some rattles (from the sliders) and some klanks (maybe the sway bar), so just be ready to deal with these issues if you get them. Not everyone gets them or some figure out how to solve them faster than others.

So, mediums might end up working out great for you, but they don't necessarily give you 2.5" lift all around. You might get more lift in the rear than the front (stink bug look), but it averages to about 2.5".

In short, the OME mediums seem to be a popular choice for expedition/camping/looking good.
 
I will buddy.
So far the front looks good, I can definitly notice the lift but it's not too extreme. It still hasn't got the weight of my ARB bumper on it yet but it's also sitting on 31" tires. I plan on getting some 315/75/16's under it as soon as I'm able to drive it to a tire shop so that will bring it up some more.

Hopefully I get it done soon. I was hoping to have it done before Christmas, now it doesn't even look like it'll be done before New Years.
 
you probably want to consider where you want to end up as far as add-ons for your cruiser when making a lift decision. If you dont plan on adding much underbody protection-ie sliders/tcase-front/rear bumpers---then id say you may want to err on the 2.5" side to keep out of harms way.

You have already stated that your rig is more expedition oriented which would imply capitalizing on low center of gravity-good mpg-and lower stress on drivetrain and would point in you in the direction of the OME low lift to provide better load handling than stock with a mild amount(1") added clearance.

With the OME low lift you are afforded the option of running the OEM toyota (tokiko) shocks which run about $100(all 4) (from Cdan)for all four and are quite the bang for the buck.
 
I have been all over Anza Borrego State park with no lift at all. There aren't many places you cant go out there with the stock height. Of course I removed the running boards first.

If you want to run 285/75R16, you could go with a minimal OME setup. If you plan on adding weight (bumpers, sliders, gear, etc.) try the 850J/863 (J spring in front, non-J in back). If not try the 850/860 combo. It will allow you to run those tires, keep your CoG low, and really improve your ride.

Oh, and if you want to run a 33" tire, and no lift, take a look at the 255/85R16. I love this tire.

BTW, we'll be heading out to ABDSP right after new years. You are welcome to join us:

http://www.oausa.net/forums/viewtopic.php?f=31&t=989
 
I wish I could tell you more about the ride quality of it but it's not completed. Slee still has not shipped me the rear pan-hard adjusted yet. I'm not very pleased about the delay in parts. I'll be calling them in the morning to inquire about it again. .

[Hijaak] All I can do is apologize about this. These are parts we have custom made and we have to rely on a machine shop to make these. I have been fed line after line on this from them. We are moving all our machining to a different shop that we do not have these issues with. All I can do is apologize. I am supposed to receive a couple next week. [/hijaak]
 
Christo not having a part is like Walmart not having a part, he's got all your 80's needs. You'll have your wagon for a long time, waiting a week a two I know seems hard, but it's worth it. In our small community of rigs, we have to wait alot on stuff. Slee is to us what Walmart is to our nation, people be hatin', but they got everything.... now, Christo, if you'd only "Roll-Back Prices"!
 
The first mod I'd like to do for my LX450 is a 2 to 3 inch lift. I live in SoCal and will be using this as a weekend warrior for camping and offroad exploring, no major rock crawling. Anza Borrego looks like the playground I will be exploring most and maybe some stuff up in BigBear. Anyway, from the searches I've done so far, the 2.5" OME w/mediums looks like it will be the best bang for the buck. Any other good options? Would be glad to hear some opinions before I make a final decision. Thanks in advance for your input.

Derrick


I recomend OME 850J front and 863 rear and 3" extended stainless lines. I got that all from Man a Fre. I used Landtank's caster correction plates.

The stock shocks will be ok with the low lift. I will be getting around to upgrading mine when I get back in the states. Many aftermarket shocks for the FZJ80 dont allow any more droop than the stockers. Stockers in decent shape (not worn out) actually do a good job of dampening even with the increased spring rate.

The panhard rod angle wont change severely with the 2.5" of lift in the rear. It could be corrected by putting in a man a fre drop bracket for the upper rear panhard mount. I think restoring the geometry like that is better than just recentering by using an adjustable panhard.

I did not do it because I am contemplating making a triangulated four link rear suspension and then it would not require a rear panhard.

Also check my write up. This is back when I put the springs in and gained a bunch of rear clearance by pulling the spare system and putting the hitch above the frame

https://forum.ih8mud.com/80-series-tech/221808-went-wrench-crazy-day-off-lift-more.html
 
I have been all over Anza Borrego State park with no lift at all. There aren't many places you cant go out there with the stock height. Of course I removed the running boards first.

If you want to run 285/75R16, you could go with a minimal OME setup. If you plan on adding weight (bumpers, sliders, gear, etc.) try the 850J/863 (J spring in front, non-J in back). If not try the 850/860 combo. It will allow you to run those tires, keep your CoG low, and really improve your ride.

Oh, and if you want to run a 33" tire, and no lift, take a look at the 255/85R16. I love this tire.

BTW, we'll be heading out to ABDSP right after new years. You are welcome to join us:

Outdoor Adventure USA, LLC • View topic - ABDSP - last run of 2008 or first of 2009

sdnative,
A friend of has invited me out there the same weekend to show me around as this will be my first trip to ABDSP. What day are you going to be there? If I can make it the same day and I see you, I'll introduce myself.
 
I purchased the Slee DIY 4" lift kit about a month ago. It was $2220.00 shipped to So Cal. So far I've got the front half completed.

I wish I could tell you more about the ride quality of it but it's not completed. Slee still has not shipped me the rear pan-hard adjusted yet. I'm not very pleased about the delay in parts. I'll be calling them in the morning to inquire about it again.

If I ever get this done ill give you more info.

Why don't you put everything on there and do the panhard later?
 
sdnative,
A friend of has invited me out there the same weekend to show me around as this will be my first trip to ABDSP. What day are you going to be there? If I can make it the same day and I see you, I'll introduce myself.

Just keep checking the link in my last post. We'll be out there on Saturday, Jan. 3. I'll PM you my contact info.
 
Hey VCCruzr,
go with the OME heavy front, med. rear. This is the best combo if you dont want (stink bug look).

The heavy fronts (850's) give you about .75 inch or more lift, but same spring rate as med's.

If you go this route, get the blue bushing's (3 deg.) from slee off-road (great service) and lift. I think mine was under a grand for everything...if you do it yourself...its not to hard.

take care...Scott
IMG_0578.webp
 
Hey VCCruzr,
go with the OME heavy front, med. rear. This is the best combo if you dont want (stink bug look).

The heavy fronts (850's) give you about .75 inch or more lift, but same spring rate as med's.

If you go this route, get the blue bushing's (3 deg.) from slee off-road (great service) and lift. I think mine was under a grand for everything...if you do it yourself...its not to hard.

take care...Scott

Scott,
The Rig looks awesome! I'm 99% sure what you have mentioned is the route I will be taking. I will eventually add a non-winch ARB so the heavy front definitely makes sense. Thanks for the pics.

Derrick
 
Hey VCCruzr,
go with the OME heavy front, med. rear. This is the best combo if you dont want (stink bug look).

The heavy fronts (850's) give you about .75 inch or more lift, but same spring rate as med's.

If you go this route, get the blue bushing's (3 deg.) from slee off-road (great service) and lift. I think mine was under a grand for everything...if you do it yourself...its not to hard.

take care...Scott

Actually the 850s are the "mediums". There is no real medium spring for the front. Just "light" (851) and "heavy" (850) then of course "heavy 3" (850J)

http://www.man-a-fre.com/technical_info/ome.htm#top

I am sure a 850/860 setup is more level than stock but The 850J/863 combo is nice and level.
 
Last edited:
Here's a heavy/med combo. ARB/M12K up front. I'm running 285s as well.

Suhweeeet!!!!! Mine will look like that someday. I can't wait!
thanks for the pics.
 
Actually the 850s are the "mediums". There is no real medium spring for the front. Just "light" (851) and "heavy" (850) then of course "heavy 3" (850J)

MAF Technical Info

I am sure a 850/860 setup is more level than stock but The 850J/863 combo is nice and level.

The 850's are HEAVY's for 2.5 in. lift
The 850j are heavy's for 3+ in. lift
The 851's are med. about 2in. lift

..Slee's site shows it as 850's heavy
851's med. not... "light".

This OME 850/860 combo twist's up good with-out rubbing the 285-75-16 STT's
IMG_0688.webp
 
Back
Top Bottom