where does this go..

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 15, 2007
Threads
77
Messages
497
Location
north vancouver
Hi Guys... stupid question.. butttt..

just did a major overhaul, engine rebuild/ paint and engine bay clean ETC Etc Etc,.... everything is back where it belongs except one lonley little wire....????:doh:

there is a wire comming out of the main harnes just above the starter that has a brass eyelet at the end. It is not a connector that needs the oppisit end to connect to, but just a brass eyelet. It looks like it would fit on the starter, but it is not for there. as as far as i remember the starter only has two connect point, one goes to the battery the other is a connector... sooo any ideas...its homeless right now... its a good size wire.... picture to follow...

thanks.
 
I think that it is a ground wire.
It might attach to the fire wall or block maybe?
 
Pic of the eyelet and a measurement from it to wherever the wire disappears and a description of the place it disappears will get you a 100% accurate place to put it from 5 mudders with flashlights within minutes. A vague description will get you a few halfhearted answers.

DougM
 
The only wires coming out of the wire main wire loom with an eyelet would be a ground wire.

The Main power loom from the battery does route down to the starter that has 4 ground eyelet wires and one eyelet wire that connects to the alternator. But that wouldn't be anywhere close to the starter.

The only two wires I could think of is the ground wire that connects to the block under the intake manifold and the ground wire that connects to the mounting bolt at the bottom of the spark control module (not sure what you call it). It is the black box on the shock tower that has a plug on the top and the wire that connects to the center of the distributor cap.

The other two ground wires connect to the front motor lift eyelet and the back of the intake manifold that should have a split connector by the main power loom.
 
Ground that attaches to manifold that is in the way when you change oil filter from top?
 
I am actually pondering the same question for my '94. The wire in question is about 10" long. In comes out of a bundle near the USDS engine mount. The only other wire coming out of the same bundle is the starter wire and that one is inside a plastic loom. It looks like the eyelet could bolt under the backside of the USDS engine mount, near the tranny cooler lines bracket.

If this description does not jog anyone's memory, I will try to take pictures tomorrow.

Thank you in advance for any wisdom (or pictures of the underside of the reat USDS engine mount! those are worth many words!),
 
The eyelet is bent at a right angle; I assume that the wire in question is the engine block ground (the harness goes straight to the battery) and that it bolts up to the boss immediately ahead and above the USDS engine mount. Could someone verify this and/or point me to a picture of that area?
 
So, do I bolt the ground up to the block above and forward of the USDS engine mount?
 
ok.. got some pics...or video... need to know the location of that ground wire if that is what it it...99% sure now that is what it is, but heres a video just for sure.. and also the location for the long wire comming out of the bottom of the coil.. there are two, one is a ground, not sure where the other goes...

thanks a ton guys...:cheers:



YouTube - landcruiser 80 wire location 2

YouTube - landcruiser 80 coil wire location
 
Keep in mind that I have a '94; I'm pretty sure of my answers, since I either left wires alone or labeled them very clearly.

1. The coil:

The short wire goes to a connector and from there to the inner fender.

The long wire goes to the #1 engine hanger.

here is a discussion: https://forum.ih8mud.com/80-series-tech/417839-rth-ground-straps.html#post5921928

Sorry about your short, I'm not quite ready to crank my engine yet...

2. The engine harness:

That wire goes to the underside of the #5 intake manifold, right next to the brake booster. The bolt goes in horizontally from the back and is highlighted with an arrow.

Here is a discussion: https://forum.ih8mud.com/80-series-tech/6563-1fzfe-need-help-identifying-wire.html#post54499 . There is a thread with a picture of that area on an engine stand, but I cannot find it right now.

In exchange, would you mind posting a picture of the top front corner of the driver side engine mount? There should be a ground point there...
short.webp
long.webp
engine.webp
 
I have a 94 as well..

the only things i have by the left mount are a battey ground and a few wiring brackets.. still to tidy up.. thats all i have there.

if you need anything just let me know. off to watch the canucks...:bang: frigging canucks better do it today or :censor::censor:...!!!!!

IMG_2652.webp
IMG_2652.webp
 
I am worried about the connector I circled (I think). That wire goes to straight to the battery (mostly, in the same bundle as the starter cable) and I believe should be grounded to the boss right next to where you seem to have it.

If it is not attached on your vehicle, all 300+ amps of starting current and being grounded through that little wire you mentioned. No wonder it's melting!

The ground with the square multi-level connector you asked about goes to the back of the intake manifold. The definitive thread (with better pictures) is here:

https://forum.ih8mud.com/80-series-tech/360727-uwdaves-1fz-replacement-2.html#post5371667

I'm pretty certain that if all *BIG* grounds are connected, your small wire will stop melting.


Good luck!
ground.webp
 
Yes, that was the problem, The block was not properly grounding with the big wire, when i took this picture i had undone that wire to clean up (remove some of the shiny new paint) so i had a proper ground. the small wire was taking all the ground. ... now everything is in its proper place. I will put up some pics later tonight... just having a breakdown right now watching overtime....
 
engine over haul pics...

1994, 265miles, the messy dripping engine finally drove me nuts..... everything came out, now its all clean and new...

new bearings, rings, machine shopped, valve job 2 yrs ago, new gaskets everywhere....etc etc etc... tons of cleaning....

here you go....

IMG_0972.webp


IMG_0973.webp


IMG_0974.webp
IMG_0972.webp
IMG_0973.webp
IMG_0974.webp
 
Can someone tell me what size bolt is supposed to be in the block for the ground cable? Tight squeeze up there but a 10mm 1.25 tap felt like it might be rite
 
Back
Top Bottom