wheel bearings question

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 12, 2010
Threads
57
Messages
253
Location
Edmond, OK
Took my sons 97 LX450 to our local Hibdon Tires to get rotation and alignment and was told that the front right shock was leaking and that had caused a problem with the bearings in the wheel. They wanted to repack them and change shocks before they would look at alignment.

I was wondering if that sounds like a reasonable thing or if I was getting an up-sell quote?
We have four OEM shocks that we have been meaning to put on. If we simply change shocks would that be enough? How would we know if the bearings really need repacked? Also, my local mechanic said it was about $400 to repack wheel bearings and that they are done in pairs. I thought Hibdons said they would just do the one side. His quote for installing the shocks was $140.

I just don't want to pay for something that we don't really need.

Thanks for the advice...
 
If shocks have "leaked" on the bearings your hubs must be missing! Sounds like you are being fed a story!
 
Time to get dirty yourself :)

Changing the shocks is super easy, you can do it yourself.

For the bearings:
- It makes no sense that worn shocks cause problems with the bearings. The shocks have nothing to do with lateral movement of the hubs.

-It is of course possible that the bearings need repacking anyway. Is there lots of grease around the back of the hub? Can you post some pics?

- There is a square plug on top of the hub, you can take that out and pump grease into it. It will fill the cavity, but not too much will go into the bearings.

-To do the bearings right you need to take the hub apart and fill the bearings by hand (and then the hub). When you do that, you might as well change the bearings and seals.

-to just pack the bearings 400 is a lot. To do an axle job way too little.

Cheers,
Jan
 
Shocks would leak inboard of the knuckles by about 8". They are not related to the wheel bearings.

Jack rig up and wiggle wheels at 6 & 12 o'clock. IF loose need to tighten them up for sure, MAYBE need a repack before allignment
 
Bad shocks will not affect the alignment on this truck.

Loose wheel bearings will affect alignment.

If the shop does not know the difference on THIS truck, don't go there, you are being fed a line to suck more money from your wallet.
 
Thanks everyone.

Is it necessary to do both front bearings at same time or can one side only be done?

Are my mechanics prices reasonable?

Are Toyota OEM shocks ok or should we do something different?
 
Toyota OEM shocks are fine and of very high quality.

You should have both sides done at the same time.

Depending on your local area and the shop rates, $400 may not be an outrageous price but if this is the same outfit that wanted to replace the shocks, etc mentioned in the first post, I'd run away. they were trying to rip you off.
 
Thanks Tom, it is not the same franchise shop that gave me initial quote. This guy is a certified mercedes, vovlo, porsche, audi and maserati mechanic that works for dealer but also has shop on the side. Very good and I have never felt taken advantage of by him. Thanks for all the help.
 
What's his hourly rate for his personal shop and what warranties/guarantees does he offer?

When I do work for folks, I charge less than the local shop rate ($65-$100/hr based on flat-rate books), but I also advise that I will take longer than the standard shop. I also charge 10% over my cost on parts and will show them my receipts. They can provide parts if they want.

I also stand behind my work for 90 days. If there is a problem directly related to what I did, I will fix it. If it's something new, it's a new charge, but I advise them of all of that up front.

Yes, I've had to eat a starter on a Ford pickup before due to something I did, but it also opened my eyes on what to do and what NOT to do.

If I provide a firm quote up front, I stand behind it UNLESS I encounter more unforeseen issues when it is opened up. Then I call at the moment I find it.

Shops rates are higher because they have more overhead, better tools (lifts), and more people and a supply chain to get the job done faster and they have the finances to back up their work.

Those that do work on the side are doing it for extra money, don't have the overhead OR Insurance (What happens if your car burns down while in their possession?) and many don't warrant their work so the risk is yours.

Both sides of the coin work, for different reasons. There are some I walk away from because I can see the problems coming, or I have concerns about the person I am working for.
 
both front shoxs and front wheel bearings are a :banana: at most.... no special skills or tools required...

absolutely something you can do on your own...

DS shox is a bit "fiddly" as the brake MC housing gets a bit in the way - but with a crescent to hold the shox in place
and a ratcheting wrench - it can easily be loosen (15 degreees at a time) and the bottom nut simply blasts of.
plenty of pics too as to the washer / bushing sandwhich... the PS shox is super super easy - especially if you have a impact gun...
also no need to jack up at all...

Bearings - aside from the mess that comes with grease packing - the only tricky part is removing the
snap ring - most don't have flat snap ring pliers - but with some fiddling and easing - it comes on and off with regular pliers.

plenty of videos on youtube and indeed tons of mudders willing to give RT help - and if you are still too intimatdated -
am sure there are mudders who will lend a hand to help you out....

bF
 
What's his hourly rate for his personal shop and what warranties/guarantees does he offer?
he charges $80 an hour and is licensed and insured. His after hours work is through his own business shop. often times he doesn't even charge me for quick things he finds while working on other things. I trust him and am sure if when he looks at the vehicle he will let me know if my original diagnosis was accurate.

Additionally, he always stands behind his work. I have never had an issue with him not looking at something a second time and fixing it if not correct.

I really don't have issue with him, just wanted to be knowledgeable when I go in to drop the car off.

really appreciate all the help on this.
 
Back
Top Bottom