Wheel bearing races

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 25, 2007
Threads
60
Messages
2,750
So I finally got around to cleaning up the old bearings and races that I pulled out of the front end, and it appears that both my inner wheel bearing races (the bigger ones) have some interesting "texture" to them. Any ideas why? Unfortunately I don't know which side each one came from.

First race
IMG_3280.JPG


IMG_3282.JPG


Second race
IMG_3281.JPG
 
How many miles were on these? Were they full of grease when you first pulled them out, or dry? They almost appear as though the metal was of poor quality and failed/fractured??(on top of what landtank said).

Wondering; does anyone make a better race than the next guy (company)?

Also, do new races come with the complete front axle service "kit" from CruiserDan?
I seem to have a chronically loose right front wheel bearing, so expect to see something like the photos above when I eventually dig into my axle.
G
 
Last edited:
I don't have any idea when these were put in, but the bearings/hubs were full of grease. I don't know if they were too loose; I did rock the wheel in/out when the truck was on the ground and didn't feel any play (not a good indicator by any means though).
 
A few guesses...

I think that is where the hot dry bearings spot-welded themselves to the races only to be broken free again.

Also, someone did a repack (thus having grease now) using the same burnt races. They may have replaced the bearings but not the races (bad idea). Bad mechanic's shortcut.

Replacing the races isn't nearly as hard as getting the !$#^!@ cone washers to come out, but you have to know what you're doing (that they're supposed to be replaced) and have the patience to tap them out a bit on each side at a time.

IMHO. YMMV.
 
I had the same wear on my trunion bearings when I did mine a few weeks back. Near identical wear to what is shown in your photos was on some of the individual bearings - though the races were fine. I replaced everything per CDan. Mine were all original at 100k miles.

Interestingly, the wheels had about 1/8" play (rocking from 12 - 6 positions) before removing them (both sides), so I expected wheel bearing / race issues - but all were fine. This was good as I didn't have replacement wheel bearings / races on hand (also per CDan :)).

Also, do new races come with the complete front axle service "kit" from CruiserDan?

Gray: CDan's kit does not include new wheel bearings or races unless you specifically ask for them. His advice to me (paraphrased as best I can remember) was that the factory units should last 300k if properly repacked when necessary. My truck had 100k miles and the wheel bearings had been repacked twice in that time by my dealer. The wheel bearings and races looked new, so I was happy.

While searching though, I did learn that most Autozones (though none near me) stock the races and bearings in the Timken brand, which is a factory equivilent. The Koyo bearings were on sale at Marlin Crawler just a few weeks ago - might still be on sale.
 
Miescha;
Thanks, will check out marlin crawler.

My 80 has 240K+, so I'm thinking, while everything is apart, might as well replace everything which is original best that I know; cause I won't be doing it again for at least another 100K (last done at 120K).

My feeling is that if these can drive through the sands of the middle east (like talcum powder) and the mud of the Amazon, my axles, with proper lube/grease, can go 100K+ before a major service. But then, I don't like turning a wrench unless something is smoking (waiting for the flying beer bottles heading my way)
:-0

G
 
Those bearings are obviously toast. Trying to analize the reason why is futile. You can drive yourself crazy trying to figure out why a set of bearings with 100,000 plus miles on them might fail. Some bearings last longer than others. Just replace them and call it all good. Why should you upset yourself?
Your brain cells are best used for making the money to buy bearings as needed. When your truck needs bearings, you need money. You need to make a living so that you can buy bearings for your truck as needed. This way your family and your truck can both be happy.
 
Those bearings are obviously toast. Trying to analize the reason why is futile. You can drive yourself crazy trying to figure out why a set of bearings with 100,000 plus miles on them might fail. Some bearings last longer than others. Just replace them and call it all good. Why should you upset yourself?
Your brain cells are best used for making the money to buy bearings as needed. When your truck needs bearings, you need money. You need to make a living so that you can buy bearings for your truck as needed. This way your family and your truck can both be happy.

I fully agree. I replaced all the bearings when I did the job last month, I'm just curious as to what may have caused those marks (I knew nothing about bearing wear before this thread) :cheers:
 
I would politely disagree with those who say why bother trying to figure out what happens(ed) in various failure situations. If you don't know why something failed, then you are more likely to screw it up the next time; ie: improper installation, improper torque, improper grease, poor quality made-in-china parts that saved you $5, but only lasted 10K miles,etc,etc,etc.

I would agree that no one should lose sleep over why their bearings or races failed, but at least look at the situation intelligently in an attempt to avoid future early failure; next time they fail you may be 1000 miles from a repair, 10,000 miles from a part, or driving through Baghdad, Mogadishu,etc, etc, etc.

g
 
Back
Top Bottom