What is correct A/C system pressure?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 10, 2007
Threads
279
Messages
11,784
Anyone know the correct pressure range for a 96 model year A/C system? (searched but couldn't find it)

My A/C is not cooling well so bought one of those do-it-yourself Freon kits and have it attached to the low pressure port. When the A/C is running on max the needle gauge is in the middle of the green ("low") or less than 25psi. Blue ("filled") on the gauge is 25 - 45psi, and yellow ("alert") is 45 - 65psi.
 
Anyone know the correct pressure range for a 96 model year A/C system? (searched but couldn't find it)

My A/C is not cooling well so bought one of those do-it-yourself Freon kits and have it attached to the low pressure port. When the A/C is running on max the needle gauge is in the middle of the green ("low") or less than 25psi. Blue ("filled") on the gauge is 25 - 45psi, and yellow ("alert") is 45 - 65psi.

Don't know what gauge you're using, but my FSM ('94 with R134a) normally functioning system shows low side 0.15 - 0.25 MPa. If MPa stands for megapascal then:
0.15 MPa = 21.75 PSI
0.25 MPa = 36.26 PSI

Wikipedia confirms pascal unit is abbreviated = Pa so this should be a good conversion.
Also warning in FSM not to overcharge system with refrigerant. It can cause "insufficient cooling, poor fuel economy engine overheating, etc." HTH
 
Last edited:
80t0ylc: Thanks, my first reading was around 15psi so added Freon to about 35-40psi. Should I let some out or just wait for it to leak out? It has a UV dye added so I'll probably start seeing the leak soon; any suggestions on the most common areas that leak?
 
Last edited:
I'll go back and check it again, forgot to increase the rpms.:o
 
Last edited:
Keep in mind this was before I knew about 'mud and the plethra of info here.... Mine stopped blowing cold, picked up a kit like yours at wally world with a built in little gauge. Filled mine per the instructions on the bottle. Been blowing cold since then. :) I dont recall the amount or "color" indicated on the bottle, but whatever it was, happened to work.

I do recall another thread on A/C here that had more tech numbers on filling.....
 
Went back and checked it at the higher idle and the low side pressure dropped about 12psi compared to idle (A/C blower on high and max cold), so added more Freon. Now at the higher rpm it reads about 24psi (at idle the needle reads about 36psi). The A/C is now blowing cold, but should I add more Freon to get the pressure a little higher??
 
Last edited:
Re-checked my '94 FSM and padre is correct: pressure should be checked with RPM at 1500. Fan speed on high and temp set at max cool. Add freon to improve performance as long as you're within specs. Does A/C feel like it's working better?
 
Yes, working much better now. Thanks.

I assumed my A/C wasn't working due to a bad fan clutch cause I never hear the clutch roar. Maybe I got the silent model:D or maybe I should still fix it (bought some silicone oil yesterday). Also found that my heater valve cable was not properly adjusted causing the valve to stay 1/4 open on full max cold. I was getting heat under the passenger seat and center console area; read about that here on mud. Disconnected the cable for now, haven't yet figured out how to pull it up to get more slack.
 
No more, put your stuff away, you are done. I like 32-34 on the low side at idle, but it varies from rig to rig. For instance, your compressor may not suck as good as someone elses. The high side pressure is less reliable when passing on figures to other owners since it is heavily dependent on ambient temperature. I'll never see below 200psi on the high side in Texas during the summer unless I have a water hose running across the condenser.

Kernal, the most common source for an a/c leak are the schrader valves. The 134 FZJ80's have 3 and they can be bought at Oreally's.
 
How many cans of freon did you add...... ???

FYI....
On the wife's 80 from empty I used 3 cans....

A factory manual when working on the AC is needed for items like this:meh:
 
Clutchee:
Hard to say for sure how much I added as I used two different size cans; one was partially filled and the other was new, but seemed like the system only would suck in or take a certain amount and no more or the pressure of the system exceeded the pressure remaining in the cans?? I would guess around 12 to 16 ounces total to bring the pressure at high rpm's from maybe 15psi to 25psi, but those are rough numbers. Agree having an FSM can't find it after a move :o

TX Cruiser:
I did notice some burbling of Freon/oil/dye from the low side schrader valve when I removed the fill hose, seemed more than I remember in the past. Maybe I can tighten them all? Need to get a tool for that. Where is the third valve: high port, low port, and ??
 
Last edited:
Clutchee:
Where is the third valve: high port, low port, and ??

Two high pressure ports right near each other at the compressor. One points up the other forward.
 
SeanAndHis80; found it right there in plain sight, the second High port :o. Went to Adv-nce Auto and bought the small tool for A/C schrader valves and saw that it's bigger than the tool used for schrader valves for tires etc. When I tightened the low side port valve it moved a very tiny bit, maybe a degree or two if that much, but it did move. Both the high pressure schrader valves were tight, no movement at all.

I did notice when I took the cap off the front/down facing high port that there was a very faint brief "psst", like pressure had built up under the cap. Also saw that both High port caps had rubber O-rings inside at the base, but the Low port cap did not; should the low port cap also have an O-ring?

After a short drive I measured the temperature coming out of the dash vents at high idle (max cold/recirculate) at 47 degrees.
 
I don't know the pressures but I can tell you it's 2.9 lbs. I checked mine at work and there was just over a pound in the system. I pushed a few buttons on the fancy AC recharge machine and it checked the system for leaks then recharged to 2.9 lbs. Now it's super cold.
 
Anyone: if the low side schrader valve leaks after tightening it, what is the procedure for removing the old valve and putting a new valve in (other than unscrewing the old and screwing in the new)? Will all the Freon blow out the low side? Seems like at that point the system would need to be evacuated completely and recharged with the correct amount of Freon and oil??
 
Changing out any of the service port valves means you will loose freon, how much depends on how fast you are. You can try to reseat the valve by unscrewing it a bit then tightening it down again. I replace them though.

1.94lbs is the max for a 94 with 134, 2.9lbs is probably for the dual evaporator systems, but I don't recall any 80's getting that treatment.

Have the machine checked Brett.
 
Back
Top Bottom