What do I do now?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 23, 2006
Threads
49
Messages
710
Location
Del Boca Vista, FL
I'm new to mud, I've spent most of my time around 80's and for the last year or so I've been working on an '82 FJ40's frame and engine. I'm at the point where I have the metal for both floor pans, rear tub floor and rear end 1/4 panel corners. I think I need to pull the entire tub off and go from there, but I have people saying I can just put the new metal in. FYI, I'm also going to learn to weld with this project, so like it or not, I have a lot of grinding to do. I'm also pulling this off in a 1 car garage, don't ask me how. I think the tub really has to come off to do it right. It's also a lot of work, but I guess that's part of doing it the right way. I plan on replacing all of the body mounts if I do pull the tub, so I will need any recommendations for who has the better set. For anyone who has done this on their own, what do you recommend? Thanks ahead of time.
 
definately remove the tub for this job. I have not done one yet but being a welder I have to say "TAKE THE TUB OFF" this will allow you to access the back side and do any replacements needed properly, after all said and done you will be happier with the results.

Good Luck

Michael
 
i'd remove the tub and sand blast it... when i did mine, i didn't want to spend the money to sand blast so i just dealt with grinding everything, well about 70 dollars later in grinding wheels I had wish i just sandblasted everything. It's cheaper then i thought and gets every little spot you would miss with ye ole grinder..


to do it correct i'd remove the tub however much of a pain in the ass that is going to be ( i've been there) call your buddies over, bribe them with beer and get them to help you move it.
 
Before you even consider removing the tub, you need to take measurements of all door openings, and weld in bracing to keep the tub properly spaced across all openings. You're removing the basic structure of the body when you cut out the floors, and you'll need inner fenders if you're doing the rear quarters, along with the roll bar bracing. If you're ever going to run a hard top or doors again, this is critical.
 
You can practice welding beads on flat piece until you feel confortable. I would also practice on welding two pieces together and ground them down as is were a body repair and try breaking it apart. Another thing you can practice is welding verticle as you are welding on a wall......not easy when you are learning. Your best bet is take a crash coarse on welding at a community college. The last thing you want is your welds to break causing you to remove your tub again. Sand blasting the frame and body will help find other problems that you would otherwise miss. Believe it or not old hot rod/low rider magazines have the info you are looking for.
 
Tub removal was pretty much my gut feeling. I know in the end it will be a much better decision. Now I need to find somewhere to keep the rest of the truck. As I mentioned earlier, the last year has been spent on the frame (removed 20 years of red clay 'preservative' & PORed surface rust) and getting it running again/well (carb rebuild, alt, water pump, fuel pump, ps gear box rebuild, ps pump, de-smog, misc gaskets & hoses). Now I know the truck is running well, so after this tub fiasco I am getting into is finished, it should run fine again. I have a garage door getting put onto my 1 car carport July 11. Once that is done, I will start removing the tub and whatever is attached to it. I also take Texx's advice about welding bracing in the doors and rear opening. It will be a slow boat to China, but hopefully I'm up and running for GSMTR in May.
 
largenfirm (mind if I just call you Kirk),

That's pretty awesome looking. Mine was originally white. Someone sprayed it green. And I'm painting it code 464 beige. I almost went with the nordic blue, but my thoughts on the S. Florida summer sun (and my wife) decided beige was the better choice. I really like the step by step photos. Those are always nice to look back on and see what it used to look like. I have posted a webalbum with my truck from the beginning. It has moved around different friend's houses, but since we bought a house last year it has been staying with me. My work space is very limited and makes it very difficult to dismantle things. The tub removal should be interesting.

http://www.landcrusher.com/projects/82greenFJ40/index.html

I'll keep lookingfor updates on your truck.
 
Hey Rumbum, the paint on your front panels looks awesome! I'm a little dissapointed you havn't restored the turn signal lights to their "original" positions on the front chassis rails!!! I got a chuckle out of that one, hilarious:D

Nice to see a square bezel too, keep it up,

Lupdog.:)
 
Back
Top Bottom