Weird brake issue

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 2, 2019
Threads
23
Messages
118
Location
Arizona
My 96 did something odd. We were on a dirt road coming down a hill with lots of washboard in the road. The ABS light comes on and was on for many miles. This is pretty common with all the washboard on the road. At one point the brakes felt spongy, much like they feel when you're out of brake fluid. Brakes still worked. I checked the master cylinder and it wasn't low. I checked all 4 caliper areas and no sign of leak. It felt like the rear brakes were working but not the front, though I cannot confirm that. I'd try to slam the brakes at about 20-25 mph but didn't feel the ABS pulse. On a hunch, I turned off the Cruiser and back on. (This always resets the ABS light). After the ABS light went out, the brakes felt normal again. This has never happened to me before. Anyone have any knowledge about this?
 
You’d toss a few lights & act weird too if you get shaken like a cocktail.

Seriously- you could’ve jarred some crap on the ABS sensor magnet, or have crap/corrosion in a socket (why I grease all of mine with either dielectric or white lithium).

These are now 2 decades old & you need to come at it more with “classic car basics”-mentality than being surprised your “Camry reliability with 4WD” -FZJ80 tosses a couple codes or acts wonky on occasion if you haven’t done a real PM of the whole dang rig.

The whole PM process is why I’m keeping mine until death. I have too many hours & parts like fusible links, headgasket, mods, etc - to rationally ever part with it.

So, if it’s new to you (guessing by your registration) - you need to go through it bow to stern, if you do the PM work it’ll restore that “I’m shocked it acted weird” -reaction.

Easy thing to start is to pull the sensors & wipe off the shmutz you find on them, take it from there.
 
If the ABS light is on normally that indicates ABS has been disabled. It will not activate and you will not get any pulsing. Based upon what you've stated I think that was the case.

Normal, stock behavior when the ABS is disabled and you exceed approximately 33MPH the ABS stays disabled until the vehicle is turned off. I expect that happened. When the CDL indicator circuit turns on it also creates a path to ground to disable ABS. I suspect that you may have a faulty CDL sensor switch or the wiring harness is shorting to ground somewhere.

That said your first statement is confusing and seems to contradict itself. What does "This is pretty common with all the washboard on the road. " mean, what is common? If the brakes felt spongy is more than likely air in the system. That can occur with heavy and prolonged braking with old contaminated brake fluid. Old fluid absorbs moisture that can boil in that scenario generating an air pocket. I suggest that you flush and bleed the entire braking system thoroughly with fresh fluid.
 
I suspect that you may have a faulty CDL sensor switch or the wiring harness is shorting to ground somewhere.

That said your first statement is confusing and seems to contradict itself. What does "This is pretty common with all the washboard on the road. " mean, what is common?

Good thinking on that harness, I want to say that was the one that hangs stupid low for what it is, right?
(I forget because I tucked all mine up)

As for the other, I thought the same - he had it long enough to figure out how to reset the light/key off, but hadn’t elevated the situation to a real fix.

And yep, brake fluid could still easily be 20yr old too, and he flashed off any water.

3/3 in agreement on your points.
 
I'm not sure I would describe it as hanging stupid low but the CDL indicator switch mounts on the front of the transfer case near the output for the front drive shaft. I can't remember how the wiring harness is routed but I'm sure it has ample possibilities to be compromised traveling extensively on washboard roads.
 
^^^ I hung mine up on a stray/downed treebranch & that motivated me when I got the Christmas lights in the cluster. That old 450 saw so many, many “hunh, never woulda thought that could happen” -moments.

If it still is on the road, I’d be amazed.

But I used what I learned to do small tweaks on the black keeper.
 
I was having issues with my ABS too. I actually pulled the ABS relay and that eliminated the issue of it pulling right on braking.

Just recently I pulled the ABS and LSPV, at the same time stainless steel lines, new booster, and master cylinder was installed as well. After bleeding the system several times to assure I was getting clean new fluid out of all 4 calipers the difference between braking now and in the past are night and day.

If your issues continue I would suggest removing the ABS, LSPV, and bleed it afterward. To delete the sensors from the knuckles, axles @NLXTACY makes a great kit to delete the ABS sensors.

As a reference I used this write up:

JeepinPete's ABS/LSPV delete
 
If the ABS light is on normally that indicates ABS has been disabled. It will not activate and you will not get any pulsing. Based upon what you've stated I think that was the case.

Normal, stock behavior when the ABS is disabled and you exceed approximately 33MPH the ABS stays disabled until the vehicle is turned off. I expect that happened. When the CDL indicator circuit turns on it also creates a path to ground to disable ABS. I suspect that you may have a faulty CDL sensor switch or the wiring harness is shorting to ground somewhere.

That said your first statement is confusing and seems to contradict itself. What does "This is pretty common with all the washboard on the road. " mean, what is common? If the brakes felt spongy is more than likely air in the system. That can occur with heavy and prolonged braking with old contaminated brake fluid. Old fluid absorbs moisture that can boil in that scenario generating an air pocket. I suggest that you flush and bleed the entire braking system thoroughly with fresh fluid.


It's common for the ABS light to come on when on washboard. It's not on typically. It doesn't come on unless there is slippage or something that would trigger the system. I thought the light indicated the ABS was being applied, because when the light's on and I hit the brakes I can feel the pulses. The light usually turns off after we get back onto smooth road. Sometimes it takes too long, but if I turn the engine off then on again the light stays off.
 
It's common for the ABS light to come on when on washboard. It's not on typically. It doesn't come on unless there is slippage or something that would trigger the system. I thought the light indicated the ABS was being applied, because when the light's on and I hit the brakes I can feel the pulses. The light usually turns off after we get back onto smooth road. Sometimes it takes too long, but if I turn the engine off then on again the light stays off.

180* out. ABS light is for failure/function disabled of the ABS (when you CDL the function kicks out the ABS for the duration of being in L range) - so you see both the CDL/TC light & ABS steady lit the entire time you run in L in the transfer case.

IDK if you have a CDL switch or any driveline mods, my answer is based as if you neither have one or done the Pin-7 mod.
 
It's common for the ABS light to come on when on washboard. It's not on typically. It doesn't come on unless there is slippage or something that would trigger the system. I thought the light indicated the ABS was being applied, because when the light's on and I hit the brakes I can feel the pulses. The light usually turns off after we get back onto smooth road. Sometimes it takes too long, but if I turn the engine off then on again the light stays off.

That is not normal behavior of the ABS system. Traveling on a rough road or otherwise activating the ABS does not turn the light on. The light on means ABS is disabled. I would have to check the FSM but as I recall the ABS light will flash if the system detects a failure. There is a procedure in the FSM to retrieve error codes similar to when the check engine light comes on.
 
Back
Top Bottom