Weber Carb Questions

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

You said you had a 38 DGES, I assumed you meant 38DGAS. I could not find a DGES in the Weber book I have.

Is your carb a two barrel? If so it should have two idle mixture adjustment screws, one at the base of each barrel. The two screws will be exactly opposite each other. Do you have an empty hole? It would explain an inability to start.

gary

I am not the original poster. I just resurrected this thread relative to my own problems with a Weber. I do have the 32/36 and it is a two barrell. Mine only has one idle mixture screw that I can see...on the valve cover side of the carb in the carb base. It is the one with the spring on it. There is not one on the other side of the carb. When I pulled off the top plate, the fuel was about 1/4 full in the bowl so it seems to be getting fuel. Thanks for the help. Great info from Gary.
 
Oops, sorry, was not paying attention. I would have to look in the book to be sure, but it makes sense. The 32/36 is a progressive two barrel; at idle, it uses only one barrel. The 38DGAS runs both barrels together, even at idle, so both barrels have idle circuits that need adjusting.

The idle mixture screw(s) not responding in an expected manor is an indication that there is gunk in the carb. I would take it apart, get a can of carb cleaner with a tiny straw, and use the straw to blow cleaner through all of the ports and pathways. Wear safety glasses. The good luck I seem to have in the potentially catistrofic situations is balanced by the little things, like the cleaner coming out of a different hole than I expected and getting a painful eye wash.

Good luck,
gary
 
I have taken the carb thoroughly apart and cleaned it well. I think it will work if I can get it adjusted right. When I took it apart the Idle screw was turned out 4-5 turns. When I put it back in I set it at 2 turns out for a baseline. Do you think it needs to be turned out more than that for a baseline?
 
One thing to add and there has been some debate on this in the past is...purchase a fuel pressure regulator and set it at ~3 to 3.5 lbs. For more years than I care to remember on two seperate applications of webers (triple 40DCOE's and twin 48IDA's) neither could or would sustain much higher fuel pressures. Having just acquired a 76 piggie with a webered 83 2F, I immediately noticed two things....1) no fuel pressure regulator installed and 2) the fuel pump has the recirc feature....which begs the question just what pressure is that 38 seeing ? My next trip out to work on the piggie w/ FP gauge in tow will answer that. Also, if any one is interested, using what pieces of the original linkage (one push clip type) found in the back of the piggie and some threaded rod, some heim joints and a clevis pin, I fabricated throttle linkage from the stock piggie pedal to the 38 complete with return spring on the carb in case any of the fab'ed linkage would crap out. It will be a while, but when I return to pig work, I can take some pics if anyone is interested in the solid linkage instead of cable.

BTW...excellent write up Gary :cheers:
 
toyman317 said:
I have taken the carb thoroughly apart and cleaned it well. I think it will work if I can get it adjusted right. When I took it apart the Idle screw was turned out 4-5 turns. When I put it back in I set it at 2 turns out for a baseline. Do you think it needs to be turned out more than that for a baseline?

I would look for a vacuum leak, the extra turns on the idle mixture might be necessary to compensate for the extra air. You should get a can of starter fliud and spray it around the base of the carb and any vacuum lines. It should make no difference to to the rpms. If the engine revs up or starts sputtering, when you spray, you have found a vacuum leak. You can also use ether, propane, even WD40.

The way I learned it, two turns should get you running.

Holley says you should never subject their carbs to more than 3 pounds, and that most electric fuel pumps (not counting those for fuel injection) are set for 7. I've played with a fuel line pressure regulator on a long paved hill to get to my house, and found that anything under 3 pounds is a problem for the Weber. So I would second the presure regulator set for 3 to 3.5.

Two other things I have in place that I find very useful in monitoring the carb is a vacuum guage and I got an O2 sensor with an air/fuel guage from JC Whitney. These are connected all the time.

gary

P.S. Thanks for the positive comments, it is appreciated, and makes the effort worth while. We like to think we don't need such things, but it still feels good to know we did something useful.:cheers:
 
Back
Top Bottom