Victory Lap

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 4, 2015
Threads
10
Messages
40
Location
Parts Unknown...(DFW)
Gather now and feign interest at the tale of Herbie the Love Cruiser and his journey!
A few months ago our family needed a dependable suv for a back-up car to the back-up car. Rather than join the ranks of moms of soccer, I decided to get the 80 series I've wanted for years.
Due to years of clean livin' on my part I was able, thru my keen use of Craig's List, to find one 5 miles from home. Having replaced the head gasket, h20 pump, fan clutch,distributor, rebuilding the power steering, upgrading the brakes, ARBing the bumper and lift kit and intsalling wacking great tires...the previous owner needed to let it go.
In my only previous post entitled "By way of introduction, a bit of blasphemy." I outlined my plans to sit it back down to stock height and refresh the seats a bit.
With the help of the members of ih8mud i was able to get the parts and advice to get it back down to Japanese specs. While that did help the drive shaft noises a bit, they weren't totally driven from my life until the new drive shafts were installed. I replaced the knock sensor in about 15 mins using the extension swivel trick i learned here. Also sorted the pesky window whistle with the forum's help. Having sold the lift kit and humongous tires to other ih8mud members i was able to move on to the seats. The originals were pretty poor. I have an upholstery man I've used on other car seats so i consulted him. Evidently his boat payment was due so with the $1,400 quote still stinging in my ears, I decided to just replace them all. With an impending road trip deadline looming over me, i gathered all the engineering knowledge I've acquired from Top Gear's Jeremy Clarkson over the years and broke out my vast collection of hammers. When that didn't work my wife broke out her vast collection of dollars and purchased four Corbeau Moab reclining bucket seats and four mounting brackets. The seats that would fit my purposes were available in the following colors: "that doesn't match" and "that reeeeally doesn't match" so we went with the former. Now, the keen witted among you will note that the 80 series land cruiser doesn't haaave 4 reclining bucket seats. It has 2 very uncomfortable front seats and a back bench that can easily accommodate 3 midgets, double amputees or meditating yoga enthusiasts...as long as none of the above want to recline.
Employing my drafting crayons, measuring tape and an eye calibrated by hundreds of half assed projects, I mounted the seats over the course of a week. The pictures will be more of an explanation than i can offer but if anyone has any questions I'll try and answer them.
The mountings are extremely solid and simple. To add strength, i cut steel strap cut into squares, and drilled them out. Backed with hardened steel bolts, nuts and washers, they are well anchored. The back passengers gained about a foot of leg room and the ability to recline while remaining at the same height as the stock seats.
The new carpeting was a challenge. American Interiors i believe. It's a solid kit that takes some trimming but they certainly don't leave you short of product to move around and make fit. Again, my wife was patiently trimming and fitting while i paced around and tried to use a carpet hammer to make it fit. I was marginally better with the KC Hi Lighter set my kiddo got me for Christmas.

Our Feb road trip took us over 2k miles, thru the Texas panhandle, the OK panhandle, across the entirety of southern CO and the San Juan mountains, over 3 mountain passes over 10,500 ft with 9% grades, down thru Albuquerque NM, across to Tucumcari and back to DFW. With the exception of the O2 Sensor going out making Wolf Creek Pass more of a white knuckle drive than it had to be, Herbie did great.

My kiddo named him Herbie in a nod to Richard Hammond's beloved Oliver when she heard the horn sounded like Herbie the love bug. When i went to fix the horn there was a protest, so it stays "MEEEP! MEEEP!" The name and the adventure have certainly endeared a 21 year old used car with 245k miles to our family. I've installed the new factory O2 sensor and packed away the Bosch that i installed in the frozen hotel parking lot for emergencies. The ladies are taking Hebie to camp next weekend so i better change the oil.
I couldn't have attempted the project or road trip without this site and the members that haunt it at all hours.
Herbie and i are both feeling 9' tall and slightly less fat after making it back in one piece. More deserving of the envious looks we get around town.

IMG_20160216_123549.webp


20160220_163909.webp


IMG_20160221_125008.webp


IMG_20160220_171640.webp


IMG_20160220_171556.webp
 
I enjoyed the read. I can't say I hate the seats. You and I have similar personalities I think. I recovered my old seats with a leather kit from a forum vendor. Even after the need to weld the seat pan and frame of the drivers seat back together I found the job to be easy. Not one hammer needed! Again, well-written and an enjoyable read.
 
Really love the seats. The leg room in the 80 series really does leave something to be desired, especially for someone as tall as me (6'3"). One question though. What do you have planned for rear seat belts. Seeing as the factory ones are pretty much useless now in stock location.
 
Nice Write up and awesome seats! I wish I had a wife that wanted to spend her collections of dollars on seats. She just wants to replace the water heater and for me to fix the leaky porch roof!
 
Really love the seats. The leg room in the 80 series really does leave something to be desired, especially for someone as tall as me (6'3"). One question though. What do you have planned for rear seat belts. Seeing as the factory ones are pretty much useless now in stock location.

Yeah, that.
 
I like the clean look of the seats. Great work
 
They aren't useless at all. The lap belts snug right to the passenger, as the seat belt clasps are anchored to the rear inside bolts of each seat. The shoulder certainly doesn't stay snugly against you when you're reclining, nor would it no matter its mounting location. The photos show the seats all the way back on the rails, that's too far back for my kid so she slides them up for riding around and the shoulder belt is then pulled back in place by the postion of the clasp .
An adult riding with the seats pushed all the way back will have to keep the seats upright to have the shoulder belts against them.
 
Nice Write up and awesome seats! I wish I had a wife that wanted to spend her collections of dollars on seats. She just wants to replace the water heater and for me to fix the leaky porch roof!
I think it had to do with her having to ride back there across the Southwest that made her part with many dollars. Though, to be fair, she also bought the land cruiser, carpet, drive shafts, pretty much all of it. And then the trip to CO too. She's not bad.
 
I think it had to do with her having to ride back there across the Southwest that made her part with many dollars. Though, to be fair, she also bought the land cruiser, carpet, drive shafts, pretty much all of it. And then the trip to CO too. She's not bad.

She's a KEEPER!
 
Ok, yeah I can see that now. I was just thrown off by the angle of the shot then. And you just pushed me over the edge of tossing the rear bench in favor of buckets. I wasn't sure it would look good till now.
 
Ok, yeah I can see that now. I was just thrown off by the angle of the shot then. And you just pushed me over the edge of tossing the rear bench in favor of buckets. I wasn't sure it would look good till now.
Corbeau also sells a nice looking bench seat that would fit as well. I have seen them mostly in Broncos. Would love to see one in an 80.
 
Nice work! :)
 
Thanks everyone! The project left me with a nice toy and some lessons in patience (which I've decided to ignore).

It also left me with a garage full of cruiser seats.
Like i said the fronts are pretty poor. The back bench and 3rd rows are fine. The front seats don't move back and forth. Looks like the plastic transfer gear that runs the power from the sides with the motors to the other tracks are stripped out but the motors themselves are fine. They also move up and down just fine. The only things i kept from my project are the seat belts.
The back bench seats also lay back. I did the hack i learned here. They have two settings, upright and flat back..no in between.
I wrote the entire post so i could say this...

Come get these seats outta my way!
I'm in DFW so if anyone needs em, come and get em.
As much help as this forum has been i couldn't just throw them away cause someone would eventually ask..."sooo, what about those seats you took out? I sure could use a kaknuter valve outta one of em..."
So if you need bits or bobs off the fronts or need a good set of back and 3rd rows to bolt in, they're of course free to you guys.
It looks like the sun is going to stop the rain for a couple hours so I'll drag em out and take some pics when i get home in an hour or so. Here's one from the original CL ad to show the color.

20150911_134428.webp
 
Back
Top Bottom