TRE zerks?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 31, 2003
Threads
38
Messages
419
Location
E. Washington
I'm replacing at least one of my TRE's on my '79 FJ40. I picked up a set of 5 TRE's made by "555". The place where my zerks are located on my old ends just have a small bolt on the new ends. Am I supposed to take the old zerks off and put them on the new ones? Do I need to buy new zerks all together?

Any help would be appreciated. I'll probably start the project tomorrow if I can get some some answers.

Thanks
Jeremy
 
i have the same TRE's 555 i got from CCOT but mine came with zerk fittings, i would at least try to install the old ones, but its easier to just by new they dont cost that much. but i would install some.
 
This is my first TRE replacement attempt. Does anyone know of any write ups or threads on this topic or have any pointers? I couldn't find too much on the issue.
 
do one side at a time and thread the new one in just as far as the old one was, that way you don't have to worry about messing up your toe in. also, the largest pipe wrench you can handle is your best friend.
 
The threads that the lock nuts use disappear into the sockets. From what I've been reading they don't actually thread into those sockets right? I can just use a pickle fork or similiar technique to seperate the relay rod from tie rod ball socket?
 
Herky said:
The threads that the lock nuts use disappear into the sockets. From what I've been reading they don't actually thread into those sockets right? I can just use a pickle fork or similiar technique to seperate the relay rod from tie rod ball socket?

I'm not really clear on what you meant here but the tie rod end is a unit with a ball joint on the end that mounts by threading INTO the tubular rods that connect each side and to the the steering components by a threaded throughbolt that comes from the ball of the unit. Each tie rod end has threads for both ends and both do thread - either into the nut that holds them in place or into it's respective tie rod. (How's that for clear?:) ) What do you mean by "socket"?
 
i believe he's refering to the tapered end of the tie rod, that the boot sits over. if so just remove the cotter pin and then the nut and incert the pickle fork between the boot and the upper part of drag link or pitman arm etc. and give it a wack with a BFH and they shold separate. hope that makes some sence. good luck!

BFH = big f---ing hammer
 
lone gunman said:
i believe he's refering to the tapered end of the tie rod, that the boot sits over. if so just remove the cotter pin and then the nut and incert the pickle fork between the boot and the upper part of drag link or pitman arm etc. and give it a wack with a BFH and they shold separate. hope that makes some sence. good luck!

BFH = big f---ing hammer

That's the conformation I was looking for. I was just leary about hitting something that was threaded without knowing for sure if was threaded into the sleeve or just inserted.

Jeremy
 
Herky,
If you have any heat available, a welding set or even a propane torch, apply heat to the part that the tierod end bolt goes through before hitting it. Get it good and hot (not melting), load the joint with a puller or your picklefork and THEN hit it. They're a taper fit and tend to get pretty solidly connected. If you just start banging hard on it cold you could deform the bolt enough to make it near impossible to get to release.
 
I bought a pickel fork from Sears but I might look into a TRE seperator. The price is right. The garage is too hot to work in right now so I'll have to wait until tonight or tomorrow morning probably. Thanks for all the help.
 
I've broke and welded back two of those HF tierod seperators. They won't do it if your tie rod ends have never been removed.
 
I ended up getting all of the rods off with a front end kit from autozone. It had about 5 different kinds of pullers and I was able to get a few of them to work. All went well until I put the draglink back together. Apparently that little clamp that keeps pressure on the TRE so it doesn't adjust itself was positioned on the outside of the draglink. When I put everything back together I put the bolt on the inside and the arm from the the steering box pushed up against the bolt and bent the rod. Toyota wants about $160 for a new one but I found a used on locally for $25 so I hope to be back on the road and driving in a straight line soon.
 
Back
Top Bottom