Transfer Case Protection

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Hellow this is my Transfer and Automatic Transmission Protection, is made by Duraluminium 6mm. Very well done, i think!!!!!!!!!!!!!.

toy80planxair0vc1.jpg


Miguel :beer::beer::beer::beer::beer:

Where can I get one of these??
:steer:
 
Wow. That looks like it'd get hung up all the time.
 
Put some removable and some non-removable sections into that, and plate it with 1/4".....bomb-proof! I want it!

That tubing is going to cause it to hang down a LOT.

Bomb proof, yeah, but you're gonna lose an extra inch of clearance.
 
Where can I get one of these??:steer:

Hellow FirstToy and Vazquez, it is made in Tarragona ( Spain ) in one of the best Welding profesional in Spain. It is Craft made, no sells in series.

Any good welding man with experience and machine for fold plates can do it, the secret is measure good with precision.

hola

In 4 hours he make the protection!!!!!!!!!!!!!!!

Hope this helps!!!!!!!!!!!!!

Regards

Miguel :beer::beer::beer::beer::beer::beer::beer:
 
found this while google searching:
frontphotoMax.php


for an hdj 80. should fit an fzj, eh?

Hellow, this protection you can find it in http://www.afn.pt/ they are in Portugal. I have installed they front differential protection. You can find it in this web site.

Regards

Miguel :beer::beer::beer::beer::beer::beer::beer::beer::beer:
 
Bomb proof, yeah, but you're gonna lose an extra inch of clearance.


i hear you, but IMHO that is a wash. I am cool with losing an inch of ground clearance for a full belly skid. Who cares about that inch when you can carry momentum to slide over something and not ruin your drive train.

I wheeled with H1 humvees once and that is exactly how they made it over some serious rock obstacles; while the cruisers crawled them, they slid over them. :hillbilly:
 
i hear you, but IMHO that is a wash. I am cool with losing an inch of ground clearance for a full belly skid. Who cares about that inch when you can carry momentum to slide over something and not ruin your drive train.

I wheeled with H1 humvees once and that is exactly how they made it over some serious rock obstacles; while the cruisers crawled them, they slid over them. :hillbilly:

See, I'd rather not lose anything more than the thickness of the solid steel plate that makes up the skid plate. :grinpimp:

Really that tubing without some plating doesn't really protect much while offering tons of hangup points. If you add plating, then you've got a really *REALLY* heavy skid plate that hangs way down.

Why not just go with a solid sheet to begin with, and skip the tubing? It's simpler, really, and provides the same protection while keeping it tucked up much closer.
 
I love my IPOR one, the only thing that kinda bums me is the two bolts for the rear drivetrain mount - they protrude way down with no protection - if you smashed a rock hard enough up against them you could bend the bolts pretty nasty or strip them so you would have to cut them off. I've been thinking of maybe cutting off the ends of the bolts so they don't hang so low, but I don't think that's entirely safe.

With proper spotting, it wouldn't be an issue, but it is one thing to think about since the IPOR plate replaces the crossmember whereas the Slee prototype looks like it covers these bolts.

shapeimage_2.jpg


-Phil
 
I love my IPOR one, the only thing that kinda bums me is the two bolts for the rear drivetrain mount - they protrude way down with no protection - if you smashed a rock hard enough up against them you could bend the bolts pretty nasty or strip them so you would have to cut them off. I've been thinking of maybe cutting off the ends of the bolts so they don't hang so low, but I don't think that's entirely safe.

With proper spotting, it wouldn't be an issue, but it is one thing to think about since the IPOR plate replaces the crossmember whereas the Slee prototype looks like it covers these bolts.

shapeimage_2.jpg


-Phil


I trimmed those bolts on my skid. Glad i did because i hit them a few weekends ago. If the bolt was still there it would have bent, making things interesting.

I guess the point i'm really trying to make is that the tube skid does hang a little low. I really think it could be tucked up a little more, but, regardless, you have so many points lower then that to get hung up on in the 80. Your control arm mounts for example, will hang as low as that skid.

anyways, all ideas are good ones IMHO.
 
Back
Top Bottom