Tranny Transfer options

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 15, 2005
Threads
30
Messages
293
Location
Western, MT
I know much of this has already been discussed... but it sounds like a sm465 is the ultimate tranny and to mate it to a 72' 3spd transfer sounds like it may take some work...also updating to a 2f from an f at the same time... I currently have a 4spd sitting on the floor waiting to be mated to the new 2f and 3spd transfer... is this not worth the effort? What would I gain by getting the sm465 vs the toy 4spd? HELP.. all of your knowledge makes me go in circles!
 
SEARCH newb...

Long story short...
2F = more torque.
SM465 = 6.5:1 first gear
Stock Cruiser 4 speed 3.5:1 first gear.
Cruiser '3 speed' t-case = 2.23:1 (or there abouts)

So you get almost double the low range with the SM465 vs the stock 4 speed.
Personally, I think the SM465's gears are a little wide for a 2F. But it still works fine.
I'd put the 2F in with an SM456 and the 3 speed t-case. Pretty solid combuination. Well know, people do it all the time (I have an SM420 with Cruiser '4 speed' t-case and have been running it a year)

Another option is an Orion T-case (4:1 low range) behind the Stock transmission. This will give a similar gear reductiona s to going to an SM420.
 
I just did the SM420 install and trail tested it last weekend. The gearing difference is amazing!! Had I known better when I installed the 2F / 4 spd / 3 spd xfer, I would have the SM420, HANDS DOWN. The SM465 will be similar in performance (1st gear, Lo range) and if you play in the rocks or run trails with 4+ or harder obsticles then the SM420 or SM465, IMHO, is the way to go for the money. The Toyota 4 spd is great on the street with 35's, but I crawled over rocks and junk last weekend that I had not been able to think about going over before. If you're running a 3 spd tranny now you won't much difference with the SM465 as far as shifting on the street either.

Bottom line: If you wheel it and like the tougher stuff do the SM465.

(and if you're interested in the SM420 I'll have a complete setup for sell soon)

Just my 2 cents...keep the change :D
 
I have done searches, and looked at all the options, but want more input...I have the 2f, 4spd, 3spd, and 3spd trsfer... some say the 4spd doesn't gain you much vs the 3spd.... I like the idea of a lower first but do you lose the upper range of 4th? What about cost? I need the 4spd transfer linkage to mate to the 3spd transfer, correct? and a gear from an adapter kit? How difficult is this to do? Is it easier done out of the vehicle..? Sorry for all the questions but just trying to get things clearer...new to the lc scene. Thanks
 
What vehicles had the sm420, sm465 in it...are they hard to find?
 
orvis17 said:
I have done searches, and looked at all the options, but want more input...I have the 2f, 4spd, 3spd, and 3spd trsfer... some say the 4spd doesn't gain you much vs the 3spd.... I like the idea of a lower first but do you lose the upper range of 4th? What about cost? I need the 4spd transfer linkage to mate to the 3spd transfer, correct? and a gear from an adapter kit? How difficult is this to do? Is it easier done out of the vehicle..? Sorry for all the questions but just trying to get things clearer...new to the lc scene. Thanks
4spd vs. 3 spd makes more difference with larger tires. Final drive ratio is still 1:1 for all the tranny's mentioned here.

What xfer linkage do you have now, vacuum or manual.

Money wise the 4spd and sm420 swap parts cost me about the same and it' not that hard to do...I did it.

SM420's 67 and earlier, SM465's after that (basically)
 
Welcome.


As stated above, the 465 is a great tranny for the deep first gear, and will operate like a three-speed on the road. Not that big of a deal to mate a Land Cruiser tcase to the back of it, or to make it work with a the Toyota three-speed flywheel housing, covered to death by many a great write up in the tech links.


Have been running a 420 in my truck since '93, and would install another one in a heartbeat if I was building another wheeler'....one of the best mods, hands down.



Good luck!


-Steve
 
orvis17 said:
I have done searches, and looked at all the options, but want more input...I have the 2f, 4spd, 3spd, and 3spd trsfer... some say the 4spd doesn't gain you much vs the 3spd.... I like the idea of a lower first but do you lose the upper range of 4th? What about cost? I need the 4spd transfer linkage to mate to the 3spd transfer, correct? and a gear from an adapter kit? How difficult is this to do? Is it easier done out of the vehicle..? Sorry for all the questions but just trying to get things clearer...new to the lc scene. Thanks

Toyota 4sp and 3sp are not much different at ythe low end and have the same final drive ratio of 1:1. It is the gears in between that are different. The sm420 and 465 have 1:1 high gear but have much lower (non-synchro) first or granny gears.

Cost is about the same for the Toy 4sp and sm420; the 465 is slightly higher because of the need to drill and tap the output shaft for use with plate style adaptors.

Sm420s were found in GM 1/2 ton to 2.5 ton trucks from 1947 to 1967 ('58 and up have a better input seal) and in military trucks (gamma goats) into the early 80s. Sm465s are found in GM trucks from 1968 to about 1990. You want one from a 4x4 that has a short 10 spline output shaft.
 
I appreciate all of the help... and suggestions... will read up!
Thanks
 
Back
Top Bottom