Towing Report

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Open invite to all mudders to come out for a pull if you are ever around Bentonville, AR---next summer.

Where we goin'? Beaver? TableRock? Lake Bentonville??! :D

Nice boat. A buddy from highschool owns the Mastercraft Dealership in Conway. I go there and drool sometimes. Always wanted a classic Stars and Stripes!

Now for the 80's tech: I have hooked up the 80 to our 25FT Mariah deckboat to move it out of storage on occasion when the Suburban wasn't around. It did sag with the OME mediums. Don't use those. Tech over.

Jwp
 
Yeah, I removed them but did not cut them up since I'll still have the 80s for decades and eventually might return it to totally stock and no towing duties. I think I just pushed the axle down with the truck's jack to make room to remove the spring and loosened bump stop together, then put the spring back on with the deflated airspring in it. There's a single bolt holding the bump stop on, then it will come/fall off with the spring. You have to do this to make room for the airspring though I think I've heard of some who left a cut down bump stop up there to compensate for longer springs. These days I think AirLift can and will recommend a different model for non stock 80s if you get the right tech.

DougM
 
OK, I'm probably going to get flamed for this, but...

Air bags are 90% cosmetic and only 10% functional for what you guys are doing.

Simply raising the rear end of the truck only brings it up to level with the UNLOADED front end of the truck. Their main benefit is that they give a bit of room for compression on the rear end - that's the 10% good. They do little to nothing for fixing the biggest issue with hauling a heavy trailer.

When you push down on a normal hitch, it compresses the rear springs and DECOMPRESSES the front springs. With less weight on the front end you are much much much more likely to have the trailer push your truck around. Air bags do not fix this 'wag the dog' issue.

Get a load distributing hitch and upgrade the receiver to match if you're going to be regularly pulling something with that kind of tongue weight.

A load distributing hitch moves the weight forward. It does this through leverage via one or more springs connected to the hitch then back to the trailer. It will bring the front end down and 25-40% of the trailer's tongue weight on the front axle of the truck - effectively nailing it to the ground where it should be.

Airbags are a cosmetic fix to a mechanical problem. They have their uses, but using them as the 'solution' to a trailer with more tongue weight than the truck is built to handle - that's simply dangerous.

IMHO YMMV
 
p14.webp


Come on Josh. The 60 does it all the time:flipoff2::flipoff2:
p14.webp
 
Grench - you do know that Toyota does not recommend a weight distribution hitch for landcruisers. That being said, I did use one...until I had the airbags installed. I much prefer the airbags.
 
Grench - you do know that Toyota does not recommend a weight distribution hitch for landcruisers. That being said, I did use one...until I had the airbags installed. I much prefer the airbags.

I believe the owner's manual states not to use a weight distributing hitch on these trucks. I'd check that first

Get a load distributing hitch and upgrade the receiver to match if you're going to be regularly pulling something with that kind of tongue weight.

The only edit I did there was to bold what you're complaining about.

Using the above poster's logic it is better to put 600+ lbs of down force on a factory hitch then jack up the back using $200 air bags so it looks right (but is unsafe) than to purchase a proper $200 receiver and $400 load distributing system to pull a $50,000 boat in a manner that is safe for themselves and other drivers.

Drawtite makes a hitch for our trucks that IS rated for load distribution for 600lbs tongue and 6,000 lbs load. It is not outrageously priced and fits quite well.

I have yet to understand how anyone can honestly argue that bags = load distribution. It doesn't.
 
The only edit I did there was to bold what you're complaining about.

Using the above poster's logic it is better to put 600+ lbs of down force on a factory hitch then jack up the back using $200 air bags so it looks right (but is unsafe) than to purchase a proper $200 receiver and $400 load distributing system to pull a $50,000 boat in a manner that is safe for themselves and other drivers.

Drawtite makes a hitch for our trucks that IS rated for load distribution for 600lbs tongue and 6,000 lbs load. It is not outrageously priced and fits quite well.

I have yet to understand how anyone can honestly argue that bags = load distribution. It doesn't.

No one's saying that bags = load distribution.

I don't see how using air bags is any more dangerous than not using air bags. Using air bags is no different than swapping to a stiffer spring, or stiffer shocks, so why would one be acceptable and the other not?

OTOH I can see situations where no air bags would be more dangerous than having air bags. Like driving at night, with your lights pointed directly into oncoming traffics face.

Toyota does not recommend or endorse the use of a load distributing hitch on an 80 Series Cruiser. They specify dead-weight only.

You can disagree, but I'm going with the guy who does this for a living.
 
Best way to set Airlift bags. Put the trailer on the ball, then lift it until it's not touching with the crank so the trailer's not putting any downforce on the hitch. Deflate them COMPLETELY as in stand/bounce on the bumper while someone opens the valves. Measure the distance from the ground to the bottom of the hitch - some spot you can also measure when the trailer's on it. Put some arbitrary number in the Airlift bags like 20psi. Let the trailer down onto the hitch until the trailer's nose wheel leaves the ground. Measure and see if you have the vehicle at the same height. If not, add or remove air and repeat. The goal is your vehicle should be at the exact same with the trailer on it as it is unladen. Remember you'll possibly have gear in the truck and in my case my family so I put 150lbs in the cargo area when I did this years ago as a wack at that weight. Then, always inflate the airsprings BEFORE you put the load on it. Once you've done it, you know what PSI to use.

DougM

Thanks!
 
Back
Top Bottom