Tough Filler Plug

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 24, 2005
Threads
87
Messages
1,511
Location
Dacula, GA
I went to change my diff fluid yesterday (first time since i resently bought the truck) and the filler plug on the front diff does not want to move. I soaked it with PB Blaster and let it sit for 3 hours and then tried it again and it still didnt want to move. The rear filler and drain plugs came out just fine. Any suggestions on what plan of action to take? I do not want to round it off and I feel like that is what I am going to do. Would an impact help? Thanks in advance for the advice.

-Nick
 
I would put on more PB Blaster and let it sit overnight. I was in the same situation, I soaked it and let it sit overnight and it practically fell out. Im thinking a impact would screw it up pretty good if it wasnt super snug.
 
I don't know what kind of tools you're using, but purchase a 6 point socket instead of a 12 point. This will decrease the possability of rounding it off to very, very small...

At least you tried to remove the fill plug first! Imagine if you had already drained it!
 
if you use an impact be sure to use the impact 6pt socket...
 
Trick I used once:

Lots of PB Blaster and a good six point socket as others have suggested, along with a good breaker bar (14" or so) and the Cruiser's jack. Line everything up so the breaker bar is near horizontal and resting on top of the jack, and eeeeeease it on up! :)

Curtis
 
I don't know what kind of tools you're using, but purchase a 6 point socket instead of a 12 point. This will decrease the possability of rounding it off to very, very small...

At least you tried to remove the fill plug first! Imagine if you had already drained it!


The Napa I went to didnt even have a 6 point socket in a 24, they were all 12 so I had to go to Advance. I was actually about to drain it first until I caught myself and I am sure glad i did.

I am gonna put some more PB blaster on it after work and try to get it off tomorrow after work.
 
Put a little sand in the socket and make sure it's clean.

I had the same issue and with a little sand to add friction, a clean bolt head, and a long breaker bar I was able to open the diff up.
 
glad to see im not the only person that has had this issue. The diff's on my old 60 came off easy so I didnt know if this was a bigger problem or a semi common issue to deal with.
 
You are on the right track just make sure the socket fits on the head well and then use a hammer to tap the breaker bar or ratchet handle. This will break bolts loose before a steady pull will. Good luck!!!
 
This will probably highlight my shade tree mechanical techniques but I heated mine with a propane torch for a couple seconds and had no problem getting them off.
 
lol i dont have a propane torch to use

This will probably highlight my shade tree mechanical techniques but I heated mine with a propane torch for a couple seconds and had no problem getting them off.
 
It actually a carry over from my shade tree gunsmith techniquies. A liitle heat goes a long way in getting stuburn flash hiders off.
 
FYI
An impact wrench with the correct socket will do far less damage to the bolt than you will without one..

Another vote for impact wrench. You will less likely round the bolt with an impact wrench.
 
Nick,
PB Blaster, Kroil, Toyopeen, or equivalent....
followed by a good amount of time to let it soak in....
followed by a good whack on the head of the fill plug with a BFH...
followed by a quality 6-pt socket and a 1/2" breaker bar...
followed by a cheater if needed ...
followed by a cold chisel if needed ...
followed by a read of this recent thread.

(Note... since Nick doesn't have a torch, he probably doesn't have an impact wrench.)

-B-
 
Last edited:
FYI
An impact wrench with the correct socket will do far less damage to the bolt than you will without one..

Another vote for impact wrench. You will less likely round the bolt with an impact wrench.

Impact = good:hillbilly:

....
followed by a good whack on the head of the fill plug with a BFH...
-B-

Hammer on the head, trying to drive the bolt in, give it some pretty good whacks, just short of caving the cover in. The alloy sealing washer is relatively soft, so will collapse, compress, slightly loosening the connection.

Sprays are of limited use here, the seal washer makes an oil tight seal, so all you are doing is washing the bolt head, it's not going to get to the threads. The threads are on the diff fluid side, so already have oil on them. Heat, vibration, impact are the best methods to remove.
 
I think I am going to stop by a shop next to my work and see if the owner can use his impact to loosen up that bolt for me before I go home tonight. He is a pretty good guy and has worked on my truck before.
 
Nick,

Let me know and I can send you another plug. I replaced all of mine with the hex plugs so I didn't have to deal with this issue. It is worth the $2.50 per plug.

So I have a bag full of old diff plugs.

Just PM me your address and I will put them in the mail.

How do you like the ironman so far.

Later,

Bomar
 
Back
Top Bottom