totally p.o.ed

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 28, 2005
Threads
71
Messages
437
Location
spicewood,tx.
the p.o. said this thing had sbc350 in it. o.k. also t/case leaked. o.k. after running it for about 400 miles i decided i was tired of filling the t/case every other day and the engine was down on #2 cyl. so ipulled the whole shooting match this weekend.

so a friend over poker gives me a good 350 4 bolt that has been taken out to 4.030. has the rods, pistons, but that is it. my plan was to pull the crank from the engine in the fj40 and put in this 4 bolt.

well after tearing it down (the fj40 engine) today i come to find it is really a 305. i do believe that the harm. bal. and the flywheel are the same, but the 305 will not work in 350 set up do to piston wieght differences.

i think i may just get a rebuild or a new chevy mex. made long block. really upset. i have built a number of sbc,s a long time ago(1975?) and they are dead simple.

maybe im just tired. any ideas? maybe this should go to chat for a rant.

thx for listening. jim:mad: :beer:
 
350 cranks are a dime a dozen. Dude probably did not know that it was a 305..
 
buddy back in high school had a bitchin 68 Vette with a Hi-po 327.............untill he blew it up, tore it down and found a 307 :crybaby:
 
buy H.P. BOOKS how to rebuild the small block chevy and H.P. BOOKS how to hot rod the small block chevy, written by Smokey Yunick (spelling) they are great books on how to build chevy's but the how to hot rod tells you how to build stroker motors and what will interchange. and some of the 350 stuff will work in the 305 i dont remember what because i read them back in the late 70's to early 80's i used it to build a 331 4 bolt stroker motor. it had a 1969 large journal 327 crank in a 350 4 bolt block, big block oil pump, 194 CC'd and flow benched heads, balanced crank, rods and pistons etc. i had about $5000.00 in it and it was in a 69 Z28 and would rev to over 8000 rpm. kick ass motor built for racing. but you can build a basiclly stock stroker cheap i just went all out on it. they are worth the read!
 
on trucks last week they had a 350 crate motor and it was less than 1800.00 its nice to rebuild but it usally costs that much here to rebuild i geuss out west its common and the machine work may be cheaper its nice to open the crate and put in the motor its also nice to see all the people on here offering you help good luck
 
What does H.P. stand for? Excuse my ignorance when it come to acronyms.:)

lone gunman said:
buy H.P. BOOKS how to rebuild the small block chevy and H.P. BOOKS how to hot rod the small block chevy, written by Smokey Yunick (spelling) they are great books on how to build chevy's but the how to hot rod tells you how to build stroker motors and what will interchange. and some of the 350 stuff will work in the 305 i dont remember what because i read them back in the late 70's to early 80's i used it to build a 331 4 bolt stroker motor. it had a 1969 large journal 327 crank in a 350 4 bolt block, big block oil pump, 194 CC'd and flow benched heads, balanced crank, rods and pistons etc. i had about $5000.00 in it and it was in a 69 Z28 and would rev to over 8000 rpm. kick ass motor built for racing. but you can build a basiclly stock stroker cheap i just went all out on it. they are worth the read!
 
Do you know what the issues are with the 305? I had a camaro with a 305 and loved it. Throttle body injection is super easy to swap on.

However, if you think you have one thing and end up with something else that is a bummer! Sorry man. Check with local engine builders/machinists, most make long blocks with a lot of power at great prices, and I have found most stand behind their work!

Just another .02

Rezarf <><
 
what is the easiest way to find out what a small block really is? i was told my cruiser has a 350 in it and after reading this im doubting it.

-miles
 
Back
Top Bottom