Tires

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 11, 2005
Threads
14
Messages
80
This is just a general question about tires.

I am looking for some mud grips. I am on kind of a tight budget being in school still and soon to have loans to pay back. I will not be doing any hard core off roading and will not be letting the air out of the tires in what little off roading I do. Was wondering if you guys knew anything about Maxxis Buckshot Mudders?

Like I say I have no plans to do serious off roading, the most I will do will be drive to the back side of our place and just get in some mud. Nothing too hairy though.
 
bought my 40 with maxxis mudders. They're ok. alot of people I know have them on their trucks, cruisers, and j@@ps. They have better tread wear than some high $ mudders too. SS TSLs are pretty cheap now too. Better for mud.
 
How does the TSL compare with the Maxxis on treadwear. Not that the Cruiser is going to be a highway baby, but it will do some travel on the paved roads from here to there.
 
Swampers, generally speaking, wil wear faster than other tires because of the soft rubber compound. Of course, attention to air pressure, rotation, etc plays a big part. A set will probably last 18-20k miles. Some people claim 30k, but it depends on driving style, climate, etc. Swampers don't wear well on hot asphalt.

If you want good treadwear and won't be spending much time in deep mud, you should look at BFG All Terrains. Good performance in everything but real thick mud, excellent road manners, quiet, and should last 50k. A 31x10.50R15 goes for about $100.

If you want the aggressive mud tire look, you're going to sacrifice mileage. Also, be prepared to pay more and get used to a lot of road noise. For the use you're describing, you might be happier with a true all terrain.

Also, what size are you looking for?
 
Road noise is not a problem with me. They will be going on an FJ 40 that I plan to keep pretty original except for maybe a small lift and possibly a tranny, tcase and axle upgrade in the future.

It will not be driven on the road that much. I've looked into some all terrains and the ones I really like aren't really that much cheaper than the Maxxis I found. It will not be a daily driver by any means.

However I did find some Super Swamper tires for 99 dollars. I don't know much about them, but they are bias ply not radial. This would mean tougher ride I know. Anyway, the tires I am looking at and considering next to the Maxxis are Super Swamper LTB.

I am looking to buy 31 x 10.50 x 15, or 32 x 11.50. The LTB's I found are 31 x 11.5 and I think that is a pretty good price for mudgrips. I would put 33 x 12.50 but all the research I have done states they will rub the rear finders on a stock suspension. The wheels I believe are 10 x 15 so I am afraid to go with anything less than 11.5's. Don't even know if 11.5's are safe on 10 inch rim.
 
JC39232 said:
I plan to keep pretty original except for maybe a small lift and possibly a tranny, tcase and axle upgrade in the future.

so what will be left stock???
 
I'm looking at the 34x10.50 LTBs for my next set. The Boggers are awesome, but for $60 less per tire plus 1" gain in height, I'm going to give the LTBs a shot.

33s will rub the fender on a stock 40 unless you trim the outer fender. You don't have to mess with the wheel well, just a little exterior sheet metal. I don't know how much room in the well is left for vertical travel- maybe someone else can comment there.

15x10 is too wide a rim for a 10.50 tire. 11.50s are pushing it. I wouldn't go that route, but that's just me. I really hate having to reseat beads. You can find a 31x12.50 and even a 31x14.50, but you've got to pony up for Mickey Thompson/ Dick Cepek ($$). I've never run either, just know they offer wider tires in a 31 height.

There are plenty of folks looking for 15x10s to fit their lifted 40s. Assuming they have the proper backspacing (less than 3.5"), I'd put them in the classified section to trade for a set of 15x8s. If you lift later, you could still run 33x10.50 on the 15x8s. I'm running 33x10.50 boggers on the old stock 15x7 steelies with a 2.5" lift-
http://groups.msn.com/FranklinPhotos/landcruiser.msnw?action=ShowPhoto&PhotoID=14

If you don't mind the less than stellar treadlife, swampers are better than most any other tire for mud or rocks. They will be loud on road, but a 40 isn't particularly quiet anyway. After a while I've come to like the distinctive hum.

As for bias vs radial, it's not as big a difference as most think. I've always run radials in the past, but my bias boggers do much better on the road than I expected. They also flatten out when aired down much better than a radial.
 
bad_religion_au said:
so what will be left stock???

Well, I meant that I might upgrade to a four speed tranny but stick with the original engine and t case. I really don't want to lift it that's only if I have to.

I posted that late last night
 
MOfj40 said:
15x10 is too wide a rim for a 10.50 tire. 11.50s are pushing it. I wouldn't go that route, but that's just me. I really hate having to reseat beads. You can find a 31x12.50 and even a 31x14.50, but you've got to pony up for Mickey Thompson/ Dick Cepek ($$). I've never run either, just know they offer wider tires in a 31 height.

There are plenty of folks looking for 15x10s to fit their lifted 40s. Assuming they have the proper backspacing (less than 3.5"), I'd put them in the classified section to trade for a set of 15x8s. If you lift later, you could still run 33x10.50 on the 15x8s. I'm running 33x10.50 boggers on the old stock 15x7 steelies with a 2.5" lift-
http://groups.msn.com/FranklinPhotos/landcruiser.msnw?action=ShowPhoto&PhotoID=14

If you don't mind the less than stellar treadlife, swampers are better than most any other tire for mud or rocks. They will be loud on road, but a 40 isn't particularly quiet anyway. After a while I've come to like the distinctive hum.

As for bias vs radial, it's not as big a difference as most think. I've always run radials in the past, but my bias boggers do much better on the road than I expected. They also flatten out when aired down much better than a radial.


We use to run bias ply on our old farm truck. Co-op Grip Spur and they did well. Anyway on to other problems. I could trade them but they are white spoke and I don't know many people that would like that look. I'm not sure they are 10's anyway. The tires on the ride are 31x10.50 all terrains that I have never heard of before.

I'm not worried about the road noise, but I realize with any mudgrip I will be sacrificing treadwear for off roading capability. As for road noise, I love the hum of a mudgrip on pavement. The more I think about it the more I like the super swampers I found. That's a great price on mudders.
 
Oh, and I'm not planning on running with low air pressure either so I don't think 11.50's would be a problem on 10 inch rims? Am I wrong? The only time I would need to worry about rolling the tire off the bead would be if the pressure were low right?

Thanks.
 
You could probably get by with 11.50s on a 10 rim if you never aired down- at all. I would make sure to never drop below 20-25 psi. Any lower than that and you'd probably lose a bead with any kind of moderate speed turn. If you kept them in the 35 psi range, you'd probably be fine. I'm no tire guy, so this is just my opinion.

What year is your cruiser? I believe 75?-up 40s came with 15x7 or 15x8 white spokes stock. Do you know for sure these are aftermarket rims?
 
Bias vs. Radial

I have a not so good friend who is telling me that bias ply tires wear quicker than radial tires. I dispute this fact because we ran bias ply on our old farm pick-up and they lasted years and years. It had what I would consider moderate road usage. Maybe I'm wrong.
 
bias plys can last as long as radials, but it depends on the rubber types of each. A bias with a hard rubber compound will last as long/longer than a radial with a soft compound.

Bias must be monitored more closely to get good wear. Air pressure is very important. I run my bias at 35 on the street, and top them off every 2 weeks or so- they lose about 1-1.5 psi/week. I think the air seepage is mostly due to old rims that weren't blasted before they were repainted, and have some crud in the bead area (PO, not my doing). It's not enough to mess with blasting and repainting, so I just deal for now.

Also, with radials you can fudge on rotation a little, but bias need a strict roation regimen for even wear.

Bias ply is the only easy way to put large lugs near/on the sidewall, so the most agressive mud tires are bias. That is changing some as mfg improvements come along, but there's still no way to put bogger or thornbird lugs on a radial. Bias are also easier to manufacture in wide sizes, and as mentioned air down better- all good for mud tires.

Radials have better road manners, generally have harder rubber compounds (sees more street use, consumers want longer treadlife), making them a little better suited for DD use. However, a bias will work well, as long as you keep an eye on them.

Keep in mind that radials are relatively new. Every tire before the mid 70s (I think thats right- some older members might correct the year for me) were bias ply.

If you can get swampers in radial for the same price as bias, then for your intended use they'd be ideal. I wouldn't spend a bunch more just to get a radial.

Keep in mind that swampers are soft and sticky. They're great for rocks/mud and do well on pavement, but were designed as a primarily off road tire. Therefore treadlife takes a back seat to performance.
 
Back
Top Bottom