Thanks to Mark W

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 12, 2005
Threads
287
Messages
3,081
Location
Littleton, Colorado
And everyone else who helped figure oput the oil problem, its not fixed yet but weve discovered the problem.

As Mark said, on the f engine cam, the oil holes are in the #2 journal, and in the 2f cam , the oil holes are in the # journal. (if you dont know we put a 2f cam in our f engine, but the f cam was shot.) so today we spent the whole day tearing down the engine to get the cam out. and sure enough the oil holes were in the #3 journal.

and now for my next question, can i just bring it to a machine shop and have them drill hols in the #2 journal? or do I need different cam?
img09727fw.webp
 
Why can't he just drill it? De-bur the holes and run it? Got drill press?



Max, sorry about the cam. I did not pay that close attention to it. My replacement aftermarket cam came drilled for both journals. All aftemarket mfr's that I saw listed one cam for both the F and 2F. Did not mean to mislead you.

At least you figured it out before you wrecked anything.


Ed:frown:
 
OK, absolution and forgiveness, I dig that. Now, do you have access to a drillpress? I'd drill it then bevel the holes. Put it back together and run it.

Still sorry.
About passing on my ignorance, but not to feel singled out, I've done the same thing to my son, no doubt!

Ed
 
Drill it and run it. I am SURE that is what the machine shop did that made that mistake on one of my customer's engines 10 years ago.:doh:

:cheers:
 
74fj40 said:
im not sure if i could trust myself to do, even though i do have acess to a drill press, a machine shop shouldnt charge more than 30$ dollars. but maybe i can convince myself to do it....
Start small, slow, Cobalt bit, plenty of oil, then use the pilot hole to drill it out to the finished size.
You'll end up with close to $30 in tools if you don't already own them, but you will be that much more wise. And you'll have some Good drill bits.
Like Mark said, drill and run.

Ed
 
max, whats the worst your going to do? let it oil even better by drilling to big of a hole? just make sure you clean it up well and i see nothing that can go wrong with drilling the holes your self, JUST dont drop it!
 
Unless you have a fairly high quality drill press and approariate setup to hold the cam in place, it is pretty easy to wind up with corss bores in the journal that are not straight.

You time is worth something.

Unless you do not have a decent machine shop available, I'd just farm it out.
 
I think you should look for a machine shop with a EDM drill (like this one) http://www.currentedm.com/MT30S.html

It's the best way for this kind of job. This machine is gonna ''burn'' you hole fast and easy, without any danger of breaking a drill , because it uses a electrode.:D
 
Well, we did find a machine shop open today and came away with another question - the guy told us that besides drilling the holes in the 2nd journal, we had another option - we could instead grind a groove all around the center of the journal - he said this would be easier, cheaper and increase the oil flow to the rockers - we opted for drilling the oil holes because we didn't really want to experiment with our engine, but his theory was very interesting - anybody heard of/done this before?
 
I've seen cams where this has been done. But you really don't want to increase the oil flow to the rockers. They don't need any more. And the lower end needs every bit it can get/keep.


Mark...
 
Mark W said:
I've seen cams where this has been done. But you really don't want to increase the oil flow to the rockers. They don't need any more. And the lower end needs every bit it can get/keep.


Mark...


Mark, wouldn't that depend on the size of the groove? I realize that the groove would provide constant oiling instead of a squirt every 1/4 or 1/2 revolution. I see why he suggested that though, because he could just chuck it up in the lathe. I would think that would be fine if you didn't get too carried away with the width/depth of the groove.

Ed:confused:
 
Back
Top Bottom