Tailgate

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 8, 2006
Threads
35
Messages
127
I've got a 79 FJ40, and i am wanting to take the top off. But...i need a tailgate to replace the ambulance doors when its off. Where is the best looking/quality tailgate i can get with the least amount of assembly to put it on?
 
I got my tailgate panel from CCOT, but you might be able to find a used one from someone on the board.

Or you could find swing out 1/2 doors, or make your own, or find a tailgate from an FST. . . but all that is more money and effort.
 
The PO of my 80' FJ40 was nice enough to include the tailgate he'd made up. it's a piece of AL Sheet metal and a chunk of extruded AL Channel. He even included the bolts! :rolleyes: I've got some wood that I'm going to make a decent one out of this summer though :)
 
Originally Posted by HappyGilmore
Bought a CCOT steel tailgate 6 months ago. Live in Iowa and guess what...rusted already. Go aluminum if you live where they use salt.

Really? They use salt in D.C., plus it gets pretty humid. I can almost watch my fenders rust. But the powder coating on the CCOT tailgate panel has done its job. No rust issues at all, and I've had it for almost a year.
 
yeah i was thinking about getting the black powder coat one from CCOT. It looks easy to put on/take off. Someone that has this one, im wondering if its sturdy? and is it just one sided and how thick is it?
 
jmode, that's the one I have, and I'm happy with it. When you first see it, it looks thin, but it's much stonger than it looks. There's an inch-wide lip around each side that makes it pretty ridged.

I'd post a pic, but I don't have any decent ones of the panel on my work computer.

edit: Just read the rest of your post. :D Yeah, it's just "one-sided" in that it's just a single metal panel. Not a hollow piece like a rear door. It's probably not more than 1/8th of on inch thick in the middle, but there's that lip around it.

Let me know if you want pics. I can post them later.
 
Ooh, found some pics.

You can see the top lip here:

carrierlatch5vh.jpg


I guess it only has that lip on the top and bottom.

You can kinda see it here, too.

rearcagefit27vl.jpg


And here's a straight shot. You can just barely make out the the "X" shape of the panel. This shape gives it more strength than a perfectly flat panel.

rearcagefitment4hb.jpg
 
A couple years ago I started to look at ways to lighten the tank.
Starting with replacing the rear doors (the small short ones) and the license plate holder/light with a sheet of aluminum.

As usual with cruiser things they weigh alot more than expected.

Those doors/license thingy weighed 24 pounds!!and the aluminum diamond plate that replaced it weighed ~7lbs

It came off the tailgate of a fullsize truck so it has a nice fold at the top.
Also it gives me about 2 more inches of room in the bed area so I could move my box back and put in the TJ rear seat.

It's light and has not rusted or been a problem. I stand on it occasionally and it has not bent at all mainly due to the "folded" top that went over a tailgate.
 
Not that I know much but PO included one that is alum. It's pretty nice but doesn't open and probably could use a bit of diamond plate. However, it is simple, doesn't rust and serves the purpose. I hope to plate or paint this one some day. My $0.02 is that this may be something that you don't necessairly get what you pay for...esp from CCOT. Have someone fab you up one (I can send you pics if you want ) or better yet, go w/ the 1/2 doors on ebay or here.

Good luck

S:beer:
 
I just used a piece of 3/16" diamond plate cut to fit. Hinges are the square ones off of my ambulance doors mounted to the bottom. A couple of latches at the top and cables to hold it level and that's about it. Basically works like a tailgate and it'll support my lard butt.
 
The pic of that aluminum fold down one would be nice...too bad I actually carry a full size spare (38sx)...all the work to open the tire carrier and then drop the tailgate just wasn't worth it for me.
I only opened the tailgate about once a year before I bolted the aluminum in there anyways.
 
I bought one of the diamond plate tailgate panels and cut it in half. I also cut off the mounting tabs. I made a pin holder for the two halves and used the original hinges to attach it. I now have a opening tailgate for the price of a solid panel.
 
I have a pair of 1/2 doors off of a 71 that I am getting ready to install. I was welding up any holes I didn't need. My dad thought I should weld the doors together, and then put 2 hinges on the drivers side, and then move the latch over to the passenger side. might look pretty sweet. Oh this is on my 78, as not to confuse anyone.

later
Ryan
 
Ryan, I'd like to see that if you end up doing it.

Thanks
Scott
 
Back
Top Bottom