Swaping sides

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 30, 2004
Threads
39
Messages
79
Ok, Tomorrow is the big day, but I still have one unanswered question, (that is until I actually get in there).

In the write ups everyone mentions puting the joint in a vise and beating the crap out of it, or sticking one end in a pipe and letting the pipe drop on the ground. Can some one give me a better description of this procedure? Also from what I read I assume that you cannot remove the clip??? so do you leave it on and shatter it when you take it apart??

Any help is desperately needed.
 
The vise procedure is outlined in the factory manual. I didn't have any luck with the pipe method. The clip pops out when the joint separates. Install a new one or use a martack.
 
The pipe method is simply this: get yourself a length of pipe at least a few inches longer than the axle (if you don't plan to use two different pipes, then measure this by the long axle). Diameter of the pipe should be such that you can easily slide the axle into it (e.g., 2-inch pipe). If you use plastic pipe, you'll want something heavy like schedule 40.

So you put the axle into the pipe with the birf end up, then just drop the pipe from a good height, letting it slide freely thru your hands. I believe most do this on a piece of plywood or something so that the axle end doesn't end up getting beat up by the concrete when it comes free. Alternatively, you could put a large rubber plug/stopper in the bottom end so that when the axle does come free of the birf, the rubber stopper cushion the fall. But you DO want the pipe to sharply hit the ground.

In the process, the clip will be destroyed and you'll need a new one from Dan.

Some people have said it takes only one drop...others say it takes 100. I've not done it yet, so I can't judge, but it's gotta beat hitting your axle with a BFH in a vise IMO.
 
I've done the pipe method. I couldn't get it to work until I figured out that the pipe I was using was too small. The axle shaft fit into it, but the c-clip wouldn't. There is a birfield retainer clip that you can't see (this is the one that breaks) and an outer c-clip that you can see. I got a bigger pipe and it came out easy.

FWIW, Bobby Long says that he lays the axle assembly on the ground (I presume the axle is elevated a bit?) and hits the bell of the birfield with a (and I quote) "BMFH".

Good luck.
 
I didn't use the pipe method (this is on a '97 LX450), I had a vise open about 2" the somewhat dropped/slammed the birf into that, about 3 or 4 wacks and it was out. I did it very gently at first then a bit harder, etc. They say the clip is not reusable, but mine looked fine, and I didn't have one anyway, so I just reused it. However, when you go to slide the inner axle back into the birf, make sure that clip is slid in nicely, on mine the axle started to slide in so I tapped the birf a bit with a hammer, and almost sheared the clip in half since it wasn't fully in it's little groove. Then I promptly sliced the hell out of my finger on it...nice blood/grease combo...so try to not do that. :)

Good luck!
 
I used a schedule 40 pipe, about 3 feet long, with a fair amount of room for the axle.

One (forceful) "drop" for the long side to separate. THree such "drops" for the short side. Did it on the concrete garage floor, with a plywood "cushion" over the floor to protect the axle end. You have to use a little force, and also lift and forcefully drop the whole assembly, including the pipe you're using. Don't just leave the pipe sitting on the floor and try to drop the birf/axle against it. Get it????
 
The pipe is awesome. It has never failed me, and I can say that the 80 series separates way easier than the 40-60 series. I did not shear the clip on either of the 80 series birfs. but all of the older ones have sheared the clip. The hard part is re-assembly. It is extremely satisfying when the first one comes apart, so have fun. And put a rag in the bottom of the pipe to prevent the loose axle from smacking on the ground.
 
I've done both and the pipe worked the easiest. The clips haven't shattered and were reused except for Eric's job which that side had issues. Get some schedule 40, 1 1/2" dia. Just be sure to have the pipe resting on the inner race of the Birf and drop it straight down so the impact is directed straight into the race. 1 drop each birf.
 
The pipe method is simply this: get yourself a length of pipe at least a few inches longer than the axle (if you don't plan to use two different pipes, then measure this by the long axle). Diameter of the pipe should be such that you can easily slide the axle into it (e.g., 2-inch pipe). If you use plastic pipe, you'll want something heavy like schedule 40.

So you put the axle into the pipe with the birf end up, then just drop the pipe from a good height, letting it slide freely thru your hands. I believe most do this on a piece of plywood or something so that the axle end doesn't end up getting beat up by the concrete when it comes free. Alternatively, you could put a large rubber plug/stopper in the bottom end so that when the axle does come free of the birf, the rubber stopper cushion the fall. But you DO want the pipe to sharply hit the ground.

In the process, the clip will be destroyed and you'll need a new one from Dan.

Some people have said it takes only one drop...others say it takes 100. I've not done it yet, so I can't judge, but it's gotta beat hitting your axle with a BFH in a vise IMO.


The pipe method works great. I used a 2 inch pipe that was a little over 3 feet long (shedule 40 pipe). I jammed a rag in one end to catch the axle shaft as it popped loose after dropping the pipe/birfield/axle from about 2.5-3 feet high onto concrete.

I also used the zip tie method for assembly to keep the snap ring compressed.
1.Place a new snap ring from CDan on the axle shaft.
2.Compressit by placing a zip tie over it. I used some dykes to tighten the zip tie as much as possible for maximal ring compression.
3.Place a little bit of new moly grease on the axle shaft and star. (make sure you are putting it back together the way it came out)
4.Pound axle shaft on with a rubber mallet and the snap ring will be placed inside the star as the zip tie slides off. Keep pounding until the axle is fully seated and the snap ring is holding the axle shaft on the back side of the star.


IMO birfield disassembly is the only way to fully clean the birf's. There are a lot of spaces for old grease to hide.


1:banana: job.....
 
Back
Top Bottom