Supercharger Install - Problems?!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 14, 2007
Threads
79
Messages
587
Location
Sacramento, CA
Hoping some of you 1FZ gurus here can help assuage my fears. Here's the situation: I just finished installing the TRD supercharger on my 1996 LX450 last night, and fired up the engine only to discover - lots of greyish white smoke coming out of the exhaust :confused:

Details - 165k on the truck, with the head gasket replaced by a Lexus dealer in 2003. New plugs, wires, fuel filter, etc., basically the engine was fully tuned up and running perfect prior to the installation. Now I've experienced a blown head gasket before, and I'm really hoping that isn't the case here, so could there be another possibility? The smoke from the tailpipe doesn't smell like antifreeze, more like fuel, and I couldn't discern any bubbles or milkiness in the radiator/overflow bottle. I drove maybe four or five miles around the neighborhood at slow speed, and by the time I pulled back into the driveway the smoke was gone. After worrying all night, I started up the engine before leaving for work this morning (the Lexus is not my DD, thankfully), and sure enough, the smoke was back. With a sinking feeling in my chest, I quickly shut it off again...

Here's one possible theory: just prior to the installation, my wife filled the tank with 87-octane, so before starting up after the install I (perhaps stupidly?) added a bottle of Lucas octane boost to the now 3/4-full tank in order to avoid any potential detonation problems before having the chance to fill up with premium. Could this stuff cause funky tailpipe smoke? Or maybe there's some kind of assembly lube in the supercharger that needs to burn off??

Thanks in advance, and let me know if I can provide any other pertinent info.
 
Relax. Mine did that too. I reasoned that it was merely the ECU resetting itself. MIne has only ever done it after the battery being disconnected. Just keep an eye on the coolant overflow tank to be sure.

On similar, but not directly connected note, the other day mine developed a milky brown deposit on the inside of the oil filler cap. I was distraught to say the least, and reasoned that it was likely because I had not driven it much save the short jaunts the grocery store and we had had some crazy temp fluctuations lately. I elected to keep an eye on it. Within the next 2 days I had to do a 2 hour highway drive and the deposit was gone and has not been back.

Karl

Tvj0h
 
Last edited:
Thanks for the replies guys.

Rookie2, I got the supercharger from trdsparks.com, I think they may still have 1 or 2 left. I also installed an aux pusher fan in front of the AC condenser and switched to 10,000 cst oil in the fan clutch during the SC install.

Landtank, nothing else added to the install, except your MAF housing and sensor, which was on there before the SC and worked great. Guess I'll just drive it easy for a while and hope the ECU adjusts?
 
Wires were rearranged on the MAF per your instructions, and as I say this was installed before the SC without issue so I don't think its the problem. I'll take it for a somewhat longer drive this evening and hope for the best.

Knorrena, so yours did the same thing after the SC install? How long was it before the ECU adjusted itself?
 
It took about 2 days once I got it running right - I had an air bubble in the cooling system.

This might sound a little wierd, but grab a handful of exhaust and smell it. Don't be surprised if it smells a little like raw fuel. At this point it should because your ecu is moving from it's uncalibrated state to state more calibrated the state of your engine.

After running it for a while, a few days, grab another handful of exhaust and it should not smell as bad as your first grab.

Trust your gut. Drive it around. If it feels wrong you will know it.
 
Last edited:
When I installed my S/C last fall it through some sort of MAF code (while running the OEM 80 MAF) on the first start up. However, I actually think this was due to my air filter being slightly damp after washing it. It must have dried up because I drove down the road about 1.5 miles to the auto store and cleared the code with their reader. MAF code never came back. I never had a problem with it blowing out strange smoke. Although my truck has always had some pretty strong smelling exhaust upon start up from cold. It usually goes away after a minute or so.
 
Sorry, no help.. but where'd you get the supercharger? I didn't think they made them anymore. You doing anything special to control temps?

Toyota just received another 100 from the manufacturer a couple of weeks ago. There should be plenty to go around for a bit. Call Cdan...he can get you one no problem.
 
Well, after about a 30-mile drive last night I think I'm in agreement with the ECU just needing to relearn. I did get a bit of smoke when first starting up (which does smell very much like fuel from the hand test), but none on subsequent warm starts after making a few stops. The truck feels very smooth and (relatively!) powerful otherwise, and the temps are just about where they were before the SC install, so I think all will be well in the end.

Thanks again for the insight and encouragement. I'll try to take some pics of the truck this weekend to share...
 
It's good to hear that things worked out. Enjoy the extra power. I started taking it for granted until a I drove a stock 80 on 275's a while back.

BTW, what type of aux pusher fan did you use? JDM or aftermarket?
 
I used this fan:

eBay Motors: 14 INCH FFD CYCLONE ULTRA ELECTRIC COOLING FAN 2600 CFM (item 110354204261 end time May-21-09 06:30:38 PDT)

I don't know if their claim of 2600 cfm holds water, but it seems to push quite a bit of air and has a lifetime warranty. Its also pretty quiet, barely audible over the sound of the engine. I had to slightly modify the vertical center brace in front of the AC condenser to fit it, I'll try to get some pics of that as well. I wired it with a Hayden relay kit to come on with the AC and/or via an adjustable thermostat. Turning the AC off and the thermo switch all the way up could then function as a "kill switch" for the fan if I had to do a deep water crossing (not likely, but we can dream, right?).
 
I used this fan:

eBay Motors: 14 INCH FFD CYCLONE ULTRA ELECTRIC COOLING FAN 2600 CFM (item 110354204261 end time May-21-09 06:30:38 PDT)

I don't know if their claim of 2600 cfm holds water, but it seems to push quite a bit of air and has a lifetime warranty. Its also pretty quiet, barely audible over the sound of the engine. I had to slightly modify the vertical center brace in front of the AC condenser to fit it, I'll try to get some pics of that as well. I wired it with a Hayden relay kit to come on with the AC and/or via an adjustable thermostat. Turning the AC off and the thermo switch all the way up could then function as a "kill switch" for the fan if I had to do a deep water crossing (not likely, but we can dream, right?).

Very nice, and at less than 1/3 of the cost of a JDM fan. I'll have to see how my temps are this summer out in the UT desert. This will be my first summer with the S/C so I've yet to see the wrath of the heat soak. I too installed the 10K oil to my new blue hub, so that should help a little.

That would be great if you could snap a few pics and post them in a new thread.
 
Thanks. Did you guys replace your HG before adding the new SC?

Mine had been replaced about 30K miles ago by the PO via the lexus dealership.
 
i heard the first run of superchargers made the computer run the fuel rich which in turn gave the cruiser terrible gas mileage and produced not as much horsepower increase as supposed to have (40-50%)over stock).
Are you guys that are running superchargers experiencing the same? Heard that was why they stopped making the SC. I was hoping the new run would solve the fuel and power issue.
 
I'm actually getting a little bit better gas mileage as long as I'm easy on the skinny pedal. My data isn't the most reliable since I did a bunch of mods within a 3 month period with little to no driving in between each mod. I was getting 11-12 MPG average city/frwy, maybe 13 on an insanely good day driving across flat Nebraska, but that was with 285's and a fouled O2 sensor. I replaced both O2 sensors, did a bunch of PM, (wires, plugs, dizzy, coolant, 10Kcst in new blue hub, etc) and threw on a S/C and an OME medium kit (a little more air drag I presume). I now have a Scangauge so I can more accurately follow mileage now and it seems like my mileage has increased. I was getting 14-16 mpg (corrected for 285's GPS) frwy over a 3K mile trip last winter. Now I have 315 and stock gears and I have not put a significant amount of miles on them to give out any meaningful data. But I'm sure my mileage will have dropped a bit.

I don't know the exact increase in horsepower I gained but it feels very significant. It's like driving a totally different truck. I have yet to hear of any significant changes Mr. T made with this second run of S'C's. As far as I can tell the new ones are almost identical to the old ones (minor bolt spacing differences on the blower housing IIRC). Besides this is one of the simplest kits out there. It does absolutely nothing to modify or address the computer/fuel metering parameters and the ECU has to just "learn" how to deal with the changes in fuel/air on it's own.

Now there were problems with putting a S/C on a 93-94 80 because of the fuel metering system that was used back then and people have had to add methanol injection systems to deal with it. Maybe that is what you had heard. It appears that you have a 97 so this shouldn't be a problem for you.
 
is changing the head gasket a must if installing a SC. I have 100,000 miles on my inline. is there an aftermarket fuel management programmer or chip?
 
Back
Top Bottom