Stripping steel

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Adventure Teq

SILVER Star
Joined
Feb 1, 2002
Threads
97
Messages
3,321
Location
Liberty Utah
Website
www.instagram.com
If it needs to be moved, sorry...

There must be a better way other than the 4 1/2" wire wheel to get that glaze off of new raw metal. Anyone have a miracle cure?

Sandblasting perhaps but I'm thinking I might need a bigger compressor.

Must be a better way.
 
Hey,
Try muratic acic, the kind you but at the pool store, or the hardware store. They call it swimming pool acid, as long as the metal is not painted, it will strip like nothing else. In fact if you dont oil or paint it quickly it will flash rust almost instantly. Muratic is also great for stripping cadmium or zinc plating off of hardware prior to welding. Been doing this for 20 years and can't say enough good things about it.
Eric
P.S. If you are using hot rolled, like angle iron or channel iron, good luck!
 
Hawk, like Ranger said, mill finish can be easily removed with lacquer thinner, well, that's what I use. Knotted or twisted wire wheel for removing finish paint, weatherstrip and such.

GL

Ed
JMO
 
On an industrial scale a hot sodium hydroxide water solution followed by a hot water rinse is used to remove oil & etc.

This is followed by a hot phosphoric acid wash and hot water rinse.

THe phosphoric acid roughens up the surface just enough to improve coating adhesion.

Any kind of acid should work. The trick is to rinse and dry it before it has time to rust.
 
No, not the protective oily coating. ;)

Yes it's the hot rolled stuff like 1/4" flat bar and 2x4" rectangle tube and such. Um those are some great idears. I'll try the thinner on it. I swear I put about 20 minutes into cleaning off that shiat on each of these bumpers and those $12 knotted wheels only last for a couple, not to mention how much it's wearing down my grinder.

I'll try that lacquer thinner and some kind of muriatric acid or something. To just wipe on let sit then wash/wipe off would be super easy and nice. And I might get munched by the grinder a little less often saving some skin here and there. :D

Thanks fellas!
 
Hawk-

I use a 3m refinishing pads. It looks like a heavy scrub pad that lives on the back of your dishwasher sponge. It cleans the metal super clean and leaves it ready for paint. They come in different "grits" I use the coarse one and it shines it up really quick, WAY faster and cleaner than a wire brush.

I just slap it onto the grinder and it cleans that "coating" off fast.

Just my .02

Rezarf <><
 
Yeah man that's zactly what I was thinking. Picked up a few at a couple different stores but they all only attach to a drill :rolleyes: so I didn't buy em. I need some heavy duty ones, you say you got em that attach to your 4 1/2"? Where'd ya get em? :D
 
Muriatic works good but put your mask on - it's some nasty stuff. Pretty cheap though.

New steel usually cleans right up with laquer thinner for me, but I use the 3m red scuff pads if there's any markings or paint on it.

Using the grinder with wire or flap sanders on it is too slow for me and gets me tired.
 
Hey,
Cold rolled steel stock does not have the scale that hot rolled does. I pretty much avoid hot rolled because it doesn't weld as nicely as cold rolled. Grinding, wire wheeling gets most of it off of the hot rolled, but some scale still remains and causes flares that contaminate the tungsten when welding. Muratic is pretty nasty stuff so be careful, gloves goggles lots of running water nearby, but works like a charm for burning plating and rust off of steel. It won't touch paint or other types of coatings though.
Good luck
eric
 
Be careful storing acids near any steel you don't want rust on! The vapors from acid will rust steel stored close to it. A buddy had a big cleanup project to save his lathe after a plating experiment.
 
Tools R Us said:
Be careful storing acids near any steel you don't want rust on! The vapors from acid will rust steel stored close to it. A buddy had a big cleanup project to save his lathe after a plating experiment.

DITTO on that and don't store it with/near metal paint cans or on a metal shelf. I made that mistake and every paint can in my paint storage area had become very rusted in a short amount of time. Doh!

I was somewhat amused during a recent visit to a local hardware store when I saw that the stores metal shelves that had the plastic containers of Acids were very rusted. At least I wasn't the only one. :D
 
HawkDriver said:
Yeah man that's zactly what I was thinking. Picked up a few at a couple different stores but they all only attach to a drill :rolleyes: so I didn't buy em. I need some heavy duty ones, you say you got em that attach to your 4 1/2"? Where'd ya get em? :D

Got mine at Lowes down the street. They were not in the grinder section but the rust romval section. These came with an adapter that uses the 4.5" grinder.

I will dig up the box and get the actual name for you.

Rezarf <><
 
Hawk Driver,

If you have a few extra dollars (and it doesn't cost much), depending on the size of the item, have the part acid dipped. Normally, it will come out with the zinc Phosphate covering on it. It's kind of hard to find places that will do this, depending on the state in which you live, but it's the best way to strip metal.

BTW, zinc phosphate coating gives good adhesion for paint.
 
Hawk-

Sorry for the delay man, the stuff is called Sandblaster from 3M. Mine came in a three pack and they really do a bang up job. I cleaned an old skid plate in about 5 minutes to bright metal with all the contours of those things, I know it would fly through your bumer builds.

Rezarf <><
 
Hey,
For just cleaning the protective grease from the steel try, acetone.
Gloves and papertowels are the ticket, musta cleaned 'bout 3miles of tubing that way.
eric
 
Thanks again guys,

I got those sandblaster 3m wheels and they do the trick. I use those flapper sanding dics for finishing off the end caps and stuff but they take too much material off to use just for removing that scale stuff.

Thanks for all the input guys, those 3m sandblaster wheels cut about 15 minutes off of the work for each bumper. :eek: They kick arse, where have I been, under a rock? :doh:

:D :beer:
 
Back
Top Bottom