Strange jolt when backing off on accelerator

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 19, 2020
Threads
3
Messages
6
Location
Bunbury
Hi guys I have a weird noise coming from the rear end of the 80 series when backing off on the accelerator, also can be heard if I don't let the clutch out slowly. Any idea what it can be?
 
It could be a few things.

Are you certain its coming from the rear?

Worn out uni joints in the drive shafts
Worn out drive flanges and CV splines on the front hubs (common in the early 80s built prior to '94)
Or diff pinion bearing failure
 
Hi guys I have a weird noise coming from the rear end of the 80 series when backing off on the accelerator, also can be heard if I don't let the clutch out slowly. Any idea what it can be?
Do you hear any metallic noise or whirl or howl while driving that usually indicates a bad pinon
 
Hydro locked rear spline, the yoke needs to move in and out as the body moves up and down. If locked the drive shaft acts like a solid pipe stressing the pinion.
I just pull the zerk and spray penetrating oil into the hole. Drive around for a bit and then re-grease.
 
  • Like
Reactions: D0g
1609772804410.webp
Be sure your buddies haven't pulled the zip tie prank on you.
 
Thanks fellas, only just bought the 80 a few months ago, what looks like an immaculate car is starting to really cost me in, maintainece , fixing little s*** like this, being a old car its probably gonna be a constant thing
 
@mud dot, your 80 once base lined will serve you well. I have DD mine 73k miles in 2 years and 9 months. While they will never be fuel efficient they make up for it in durability and thousands and thousands of miles of trouble free service. You will have to spend some money base lining the rig (there are many good threads on doing this) but most of the list can be done a little at a time.

For now you need to check your u joints and spline and slip for play/wear. Check your front and rear diff fluids as well as the transfer case fluid. If you haven't drained them and filled with new fluid start your base line draining the rear and inspecting the fluid you remove. Then do your front diff. Then your transfer case. Inspect for metallic particles, milky looking fluid, dirty fluid, etc. Refill and drive. I am not sure how much you drive or if it is your only rig but with an 80 there are always options.

I lost an hub seal once (PO installed hub seal incorrectly) between Brevard and Bristol and by the time I realized it the rear end bearings were brinelled noisy. Being 10 hours from home on a Sunday with work on the Schedule for Monday; I replaced the seal, filled the diff with 2 pints of STP Oil Treatment and some 80w90 and 18 hours later I hit the driveway, showered and headed to work. Funny thing was the bearings were quiet all the way home and the 80 got me to work and back all week before I tore the rear end apart and installed bearings that weekend.
 
Thanks fellas, only just bought the 80 a few months ago, what looks like an immaculate car is starting to really cost me in, maintainece , fixing little s*** like this, being a old car its probably gonna be a constant thing
I hope you went in to this beasty with your eye's wide open. The youngest of them are 23yrs old. They need some maintenance. I've been daily driving mine for 2 1/2 years and 30K miles. The only time it has not moved is when I have something torn down for PM work. In 2 1/2 yrs and 30K miles, that's not much down time.
Bought it at 211K and she just rolled 240K.
Just changed all the wheel bearing this past weekend because one front one was toast, while "in there" I decided the rear calipers were just too crusty to keep going; they blew a seal when reseating the piston and hemorrhaged rusty brake fluid all over the drive. I just bled them a month ago till clear fluid drained, so obviously they are toast.
What I'm getting at is: they are old, and many parts are tired, get used to it.
Its unbelievably reliable for its age and mileage, but it takes work to keep it that way.
 
Thanks fellas, only just bought the 80 a few months ago, what looks like an immaculate car is starting to really cost me in, maintainece , fixing little s*** like this, being a old car its probably gonna be a constant thing

You haven't said what year yours is.
The newest 80s are 22 years old. They are built tough and reliable. So much so that they can be neglected for years and still be going strong.

It can seem like there's always little things to fix. But understanding that it is part of owning an old car helps.
Baselining is not a word Aussie's really use, but if you do some searching here, there's plenty of threads talking about baselining, or catching up on neglected maintenance to get the old girl back to a reliable state.
A word of caution, members here can tend to get a little obsessive and go over the deep end on what is "essential" in terms of baselining, so read with discretion.
No offence to USA owners intended at all, but the attitude to ownership is different compared to Australia. In USA, they are a fairly rare vehicle and a novelty owned mostly by enthusiasts.

If you are someone who is inclined to fix things yourself, a lot of the typical overdue maintenance is stuff you can do at home.
If you'll be paying someone, this can get expensive.

I purchased a 93 model about 3 years ago. I paid $5k for it in Sydney. It was in decent shape, but not immaculate.
I bought it knowing I would probably put another $5k into it over the next few years catching up on neglect, improving things and some minor upgrades.
I also bought it knowing that with a 25 year old vehicle, there's a possibility of big ticket items falling. Eg, I have replaced a starter motor, alternator, head gasket, and have a clutch kit waiting to be installed.
But I also bought it knowing it was a long term prospect, not a short term whim. Even with repairs, I still have a vehicular that suits my lifestyle, is tough, is great for weekends away, and I enjoy driving it every time I get in it.
I also enjoy working on it myself

I tend to use genuine OEM parts, or quality after market parts. It pays off in the long run with reliability, and certainty over the quality and reliability.
Sourcing quality parts without paying full price at a toyota dealership is something that makes a huge difference too.
 
I am sooooo stealing that!
Works on front CV shafts as well! Start with a 3/16" wide zip tie and work up to the 3/8" wide ones over a week. Just don't get caught in the employee parking lot under the Head of HR's car.🤪

I kept telling him it was the Fetzer Valve going out on his Escape.
 
Back
Top Bottom