strange internal carb leak?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 6, 2005
Threads
16
Messages
112
Location
Boise, ID
So I'm trying to pass emissions, I did the regular stuff and got my numbers pretty close. Since the end of the month, and my deadline, is coming up I went to a local mechanic today. I'm trying to solve a running rich problem which causes high CO at speed. At first he thinks my fuel pump is putting out too much pressure, and then spots this strange carb leak. I took a picture of it, sorry for the quality. The circled area is gas coming in from the edge of the metal ring below the venturi (?). The mechanic said he didn't know if this is something you can fix with a rebuild, or if I need a new carb altogether. I sent a note to Jim C. today asking the same thing, but thought I'd throw this out here too.

Thx for the help.

Tim
 
Last edited:
Also, the gas only appears there when you rev the engine. At idle there is nothing. I suppose this is why my idle CO readings are well within spec and the 2500 rpm ones are double the limit.
 
Last edited:
Hmmm, lemesseee.... What year is your rig, and what emssions numbers do you need to meet? Is your rig stock; i.e. carb, cam, emissions systems, ect...?

I can't tell where you have drawn the circle due to picture quality. Fuel may be visible at or near the bottom inside lip of the venturi when the engine is at mid to high RPM's. Fuel will also be visible coming from a small hole or slot just a few thousandths above the throttle plate when idling.

Be very carefull when making these observations, though, I have met more than one individual with melted facial skin due to carburator backfire.

Even if you do see fuel at these points, it is not an indication of rich or lean exhaust emissions. High fuel pressure is an unlikely culprit for rich exhaust under load, but could easily (and should) be ruled out. Check pressure at idle and under load.
Hope any of this helps.... I'll check back soon.
 
Here is another shot. The gas appears where the arrow is pointing. I'm pretty sure it is coming up from behind that ring. It kind of bubbles up from there. Also, take a look at the gouges on the rings on both barrels, is that normal?

By the way, It is a 1971 FJ40 with a stock carb. Here is a link to my emissions numbers, if you are interested... https://forum.ih8mud.com/showthread.php?t=67198

The mechanic tested the fuel pressure, he said it wasn't causing my problems. It rang in at 6psi.

Thanks again, I admit I am a carb noob but learning quickly. :cheers:
 
Last edited:
Hi Tim,

Much better pic of your carb. Fuel should NOT be bubbling from that area. The "ring" you mention is the top of the main venturi. I don't believe that there is a fuel passage between the main venturi and the carb body (fuel bowl housing). I have literature at work; I will look it over tomorrow and drop you a line. Do you only see fuel "bubbling" from this area when you press the accelerator??
The "gouges" are marks from the initial carb assembly when the venturis where staked into position.
 
Thanks Dan. Yes, I only see the fuel there when I rev the engine.

I looked at it with the mechanic today, and went out and just looked again. I think he is wrong, the fuel is coming from the left of the arrow and swirling around to where he thought it was coming up. I looks like it bubbles up, but I don't think it really is. He also thought those gouges were marks from some botched rebuild in the past. I think a new mechanic may be in order.
 
Last edited:
Hi Tim,

I looked over my carb rebuild info today, but it didn't really clear up anything for me. I was trying to determine if there is a fuel passage between the carb body and the staked-in venturi. I don't believe that there is.

Well, starting from the basics with regard to high CO readings at high RPM, I would 1) make sure your air cleaner is clean 2) make sure the choke is operating as it should 3) verify the float adjustment level (easily done on many Asian carbs via a small window on the side of the float bowl. A normal level in the window will register the fuel level between the two points [upper and lower] on the window bracket) 4) verify condition and operation of the fuel evaporative canister system. I am not sure your rig has this; it came along in 09/1971. 5) if everything above checks out, you likely have an internal carburator issue.
I hope you don't have to go this deep into it, but if you do, you may be better off; i.e. - improved feul mileage and/or performance.
Good luck and lemme know what you find.
 
It is hard to tell where it is coming from from the pictures, but there ren't too many possibilities: bad gasket or a cracked housing. If the top cover gasket were leaking, you still wouldn't expect to have fuel leaking out because the fluid level should be only half way up the bowl.
 
Back
Top Bottom