steering shaft splines exposed-normal?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 27, 2003
Threads
182
Messages
4,622
Location
Socal
just wondering how much of the splines exposed is normal? it looks to have always been this way judging by the dirt on the splines- but thought I'd check w/ you guys
081907_15101.webp
 
i just noticed that on my rig too and was wondering the same thing
 
Mine is the same. What year is yours FirstToy? Mine is a '92. I'm not sure if it is that much, but there seem to be subtle differences on the FJ80's vs. the FZJ80's. I imagine it is normal so that it can compensate for flex but I really don't know for sure.
 
James-checking your box after all the excitement last weekend? I ran out and looked at mine-same story here. It must be OK.
 
Group think at its best!!

We're all guilty of it....see something break, destruct, fail that we haven't thought of and all of us are out looking at our rigs.

Probably one of the reasons I don't come here that often...too much paranoia on everyone's part....

-o-
 
Group think at its best!!

We're all guilty of it....see something break, destruct, fail that we haven't thought of and all of us are out looking at our rigs.

Probably one of the reasons I don't come here that often...too much paranoia on everyone's part....

-o-

No kidding; sometimes I think this site is giving me an ulcer from all the worrying about X being just right and Y being adjusted so. Oh well, comes with the truck I guess! ;)
 
No kidding; sometimes I think this site is giving me an ulcer from all the worrying about X being just right and Y being adjusted so. Oh well, comes with the truck I guess! ;)

My course of action to mitigate the paranoia propounded here is to stick to a very regimented PM schedule on all fluids and parts. Set up a schedule, be disciplined and go with it. Get parts from Dan or your favorite parts location and be consistent. That is all these trucks really need. You go wheeling, check your s*** afterwards. Your truck sits for a long time, be pro-active in storing it. Use it as a DD, then treat is at a DD. Beat the s*** out of it, pay to play.

-o-
 
My course of action to mitigate the paranoia propounded here is to stick to a very regimented PM schedule on all fluids and parts. Set up a schedule, be disciplined and go with it. Get parts from Dan or your favorite parts location and be consistent. That is all these trucks really need. You go wheeling, check your **** afterwards. Your truck sits for a long time, be pro-active in storing it. Use it as a DD, then treat is at a DD. Beat the **** out of it, pay to play.

-o-

THAT is probably the best post I've seen on this site so far ;)

So true though...as it is with any rig you own I suppose.
 
I have a 96
I feel better now :) thanks guys

For the steering, I'll be paranoid (ie; safe). After seeing what can happen, it really is life and death. Everything else is an inconvienence.
Steering breakage... see you in the next life!
 
Honestly I should be able to remember if that's normal or not since I've had that shaft out before. Since everyone else has it I say it's normal ;)

One thing I do know is that the shaft needs to be as far forward into the steering box as possible to eliminate clicking noises from the rag joint. Also that shaft has a set screw locking it to the steering box. If you're truly paranoid, just remove the splash plate above where the shaft meets the box and check the set screw.

The plate can be seen just left of the arrow in the photo.
 
Oh yeah, the shaft also only goes into the box about an inch.
 
...you mean the box with the bent sector shaft and twisted splines? :hillbilly:

Hehe, yep. I'm on a rebuilt box but am still not satisfied after driving Devin's truck. His steering was much tighter than mine. Any word yet on the 35mm shaft?

Also I thought you were going to make another joke about a box and only getting the shaft in about an inch. :eek:
 
ah, sexual innuendo with my first cup of coffee...

try tightening up the pre-load in your (or her) box for a tighter feel...

I did that on my previous box and it caused me to get a remaned box. I'm afraid of the pre-load now. I'd like to pre-load it to FSM spec (and assumed it was), but I need some gauges.
 
My course of action to mitigate the paranoia propounded here is to stick to a very regimented PM schedule on all fluids and parts. Set up a schedule, be disciplined and go with it. Get parts from Dan or your favorite parts location and be consistent. That is all these trucks really need. You go wheeling, check your s*** afterwards. Your truck sits for a long time, be pro-active in storing it. Use it as a DD, then treat is at a DD. Beat the s*** out of it, pay to play.

-o-

This is the most concise, logical and correct post I've seen in months. Wish I could publish it word for word!
 
Back
Top Bottom