Starting my Hj45

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 2, 2014
Threads
1
Messages
9
Hi Guys, I'm looking for some help with a couple of starting problems I'm having with the diesel...
When I start from cold, I glow until the coil shows red, crank the engine and she fires and runs for about 3-5 seconds then stops. I can immediately restart her and then she's happy. If I drive down the road about 2 k's, leave her for 2 hours, she'll start and run fine. Seems to be only when she's dead cold.

Now I'm having problems getting her to crank, irrespective of whether she cold or hot. I can hit the starter and just click from a relay somewhere inside the cab. Several attempts and then she'll start cranking and then the above scenario takes over..
I had to have a brand new starter fitted about 2 months ago as the old one was dying a slow cranking death...

Any ideas?

Cheers
Chris
 
Check the following..

My 3B (might be different) has an oil pressure switch. Sometimes when it is cold the oil is thick enough that the pressure doesn't build right away and the EDIC shuts the fuel back off again. I believe there is another relay controlling this as well,but not sure on your truck.

As for the starter not rolling, but getting a "click" you likely have a bad electrical connection on your main power feed to the starter, or a bad ground on your engine block back to the chassis, or from the chassis back to the battery. Make sure all the main electrical connections are clean and tight, and by that I mean if they feel tight, take them apart, wire brush them, and then put them back together, tight! This symptom is saying that the starter solenoid is getting power, but the main power feed is not supplying sufficient voltage for the starter to crank over.
 
new glow plugs, new glow relay, new starter relay, new 2ga electrical cables to the starter and grounds, then clean every electrical connection on that side of the engine bay.

Should cost around $200 and if that doesnt solve the problem you have to look harder. Its a pretty simple diesel engine this will solve most starting issues.

No oil pressure shutoff on the HJ45, the EDIC controller was introduced in the HJ47 (2H engine)
 
Errr, I would suggest reversing the order above... Mucho cheaper to clean and tighten all the connections before replacing them along with a bunch of parts that may be perfectly fine...

Good to know on the EDIC, I wasn't sure where that whole mess started.
 
Thats a good point if trying to save money it could be done the other way arround, Its just one of those things I would do, as you could solve the problem in an afternoon rather then be chasing it down over time.

My truck is a daily driver, so reliability is a must!
 
Well I now off the road. :crybaby:

Car wont even try to start. I'm thinking low battery voltage? I know I have an average battery, but this is because I'm only getting 13.5v charging IF I can get it started.
Connections are good, starter is brand new. Does the glow plug relay stop cranking if the plugs aren't hot enough? I'm not familiar enough with the electrical system in these to try and diagnose. Sometimes repeated on/off of the ignition will get the starter cranking, but it's been getting worse until no go at all 2 days ago...
 
So its not cranking at all? not even a little weak turn? Is there any noise coming from a loose spinning starter motor?

If not then its the starter relay or solinoid or a totally rooted starter motor.
 
Or the wire from the ignition switch is not giving power to the solenoid. I'd check that before tearing into other stuff..
 
....Car wont even try to start. I'm thinking low battery voltage? I know I have an average battery, but this is because I'm only getting 13.5v charging IF I can get it started.
Connections are good, starter is brand new. Does the glow plug relay stop cranking if the plugs aren't hot enough? I'm not familiar enough with the electrical system in these to try and diagnose. Sometimes repeated on/off of the ignition will get the starter cranking, but it's been getting worse until no go at all 2 days ago...


When you own a diesel it is most essential to have a battery/batteries in TOP condition (and many of us also choose fit the largest/highest-CCA version we can in the engine bay too).

I think it is also essential to own a battery charger so you can recharge (& therefore revitialise your battery/batteries) whenever you've drained it/them after those many unfortunate incidents (that are bound to happen if you're a DIY-er) whereupon you find your vehicle reluctant to restart after some tinkering/repairs/maintenance you've carried out.

(With a charger, you can go to bed with the satisfaction that, in the morning, she'll be turning over nice and fast again giving you a much better chance of finally firing her up.)

:beer:

PS. No... There is no lockout in the electrical system that prevents cranking when the plugs are not up to temperature..
 
Thanks guys.

I'm thinking starter relay. As i said earlier, it has a brand new starter motor, fitted when I had the car in for a fuel injection problem. The old one was slow at best (I suspected the battery) but it died when they were bleeding the system..
Basically over the last few days I have randomly tried cranking it. You hit the key, you can hear a click in the cab and the servo in the engine bay that has something to do with the injection system. Each time I've tried (with no glowing as I didn't care if it started or not) sometimes it started cranking, others it did not. Some of these were after the battery was charged all night, other times it had just been sitting in the shed. All the connections are tight, so I guess a relay is a good place to start?
Now all I have to do is find one for sale, are they still available via the normal spares suppliers or are these like rocking horse doo?

Once this is sorted, then I need to establish why it stalls after 3 or 4 secs (on cold starts) and then can be immediately restarted... I thought I might not be glowing enough?
Then I can hunt down a voltage regulator as it's only putting in 13.5v after starting....

Thanks in advance for the advice too..
Cheers
Chris
 
yep its defintily a starter solenoid or a grounding issue (but id start with the solenoid)

As for why its stalling is it a H or a 2H engine.
 
Solenoid or relay? I assumed the solenoid would have been changed with the starter. Aren't they usually integrated?

It's an H motor. On the second start, the buzzer can still be squealing as she runs and if you hit the glow again, it sometimes goes to stall, but saves itself, misses then keeps going
 
I'm guessing you have a bad ground. This sounds identical to my HJ47 when I first got it. If you have already cleaned up ALL of the ground connections (battery to engine, engine to frame, etc...), then I suggest replacing the cables. Over time your cables can build up a ton of galvanic corosion residue inside them. If your cables are original to the truck, they could look fine on the outside, but allow for very little actual condution or grounding. It is also another cheap item to replace & eliminate one more from the list.
Best,
Abe
 
....I had to have a brand new starter fitted about 2 months ago as the old one was dying a slow cranking death...Chris

Hi Chris...

About the new starter.... I'm surprised you could buy a new one for such an old vehicle (HJ45).

Did it come from Toyota? Do you have a part number?

.....
I'm thinking starter relay. .......Basically over the last few days I have randomly tried cranking it. You hit the key, you can hear a click in the cab and the servo in the engine bay that has something to do with the injection system. Each time I've tried (with no glowing as I didn't care if it started or not) sometimes it started cranking, others it did not. Some of these were after the battery was charged all night, other times it had just been sitting in the shed. All the connections are tight, so I guess a relay is a good place to start?
Now all I have to do is find one for sale, are they still available via the normal spares suppliers or are these like rocking horse doo?

Once this is sorted, then I need to establish why it stalls after 3 or 4 secs (on cold starts) and then can be immediately restarted... I thought I might not be glowing enough?..

A bad battery can cause "clicking rather than cranking".

Have you tested your battery performance under load?

This is a great old tool I use:
BatteryTest.webp



...Then I can hunt down a voltage regulator as it's only putting in 13.5v after starting....Chris

Don't rush into replacing your VR... When a good battery has been heavily drained (as it will be during cranking when hundreds of amperes of current are drawn from it) it will always tax the alternator making it's output voltage appear low like this.

Similarly, a poor battery that refuses to charge properly can produce the same result..

At 13.5V a good battery should be accumulating charge and only when approaching fully-charged status will you start getting readings of 14V and above (particularly with the standard low-output original alternator).

Solenoid or relay? I assumed the solenoid would have been changed with the starter. Aren't they usually integrated?

It's an H motor. On the second start, the buzzer can still be squealing as she runs and if you hit the glow again, it sometimes goes to stall, but saves itself, misses then keeps going

Yes the starter solenoid (which is a very common cause of "click but no crank") should have been new with the new starter.

Starter relays are far less likely to cause trouble ... but it's not unheard of. (As for whether they're available or not... I can't even tell you a part number because I know nothing about the build date of your HJ45.)

:beer:
 
Just thought I'd update and say thanks for the input from everyone. I started at the cheapest end of component replacement and bought a new battery and charge regulator. Hey presto, problem solved!
Turns over like crazy and no more refusal to start.

I haven't solved the start, stall then restart and run problem, but I can live with that seeing as its only when on first cold start...
Seems the glow relay clicks after a few seconds of running and she stalls. Restart with a bit more glow and I'm away...
Cheers
Chris
 
You sure that's the glow relay clicking, and not a low oil pressure shut down? My 3B would do that below -30C. Low oil pressure is telling the EDIC to shut off fuel. Second start has built enough oil pressure to keep running... Just a thought...
 
Thanks, but as mentioned earlier, it's an H engine, the edic came on the later motor, so can't be anything to do with oil pressure.
Cheers
Chris
 
...
I haven't solved the start, stall then restart and run problem, but I can live with that seeing as its only when on first cold start...
Seems the glow relay clicks after a few seconds of running and she stalls. Restart with a bit more glow and I'm away...
Cheers
Chris

I don't understand why your glow relay should click after a few seconds of running Chris...

Surely your preheat is finished as soon as your engine fires up and your key hits the run position..

Maybe you're hearing your voltage regulator click instead of your glow relay?

A solution to "stalling on it's first start in the cold" might be to install a separate momentary-switch so as to provide manual afterglow (as Toyota did on various cold-climate-destination models that have your "manual glow with glow controller preheat system").

Are you in a cold-climate region?

:beer:
 
Hi, the Hj45 is a manual glow car (button on the dash), so no separate preheat is required.
I'm in Melbourne (35 degrees today) so no, not cold climate. The new voltage regulator is solid state and has no relay contacts.
It may not be the glow relay, but there is only that and the starter relay under there...

Cheers
Chris
 
Hi, the Hj45 is a manual glow car (button on the dash), so no separate preheat is required.
I'm in Melbourne (35 degrees today) so no, not cold climate. The new voltage regulator is solid state and has no relay contacts.
It may not be the glow relay, but there is only that and the starter relay under there...
Cheers
Chris

Hi again Chris

I thought an HJ45 normally had its preheat controlled by the key (and that a dash -button was provided as an extra only to provide afterglow in cold-climate destinations)?

Here's a page from a 1975 owners manual that seems to support this view:
1975ownersManual.webp


What year is this HJ45?

:beer:

PS. Melbourne is quite a bit warmer than here so cold starts should never be much of a problem
 
Back
Top Bottom