starter issues again...

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 24, 2003
Threads
56
Messages
327
Location
phoenix
I replaced the contacts and plunger(kit) in my starter about 4-5 months ago. Started fine. On Friday,turn the key and "click". Before I could crank it a few times to get it crank, not this time. Its officially dead.
1. I hear a click, telling me I DONT have a ignition problem, correct?
2. The click is the solenoid? if so, I assume its working then?
3. Its the original starter, time to replace the whole thing?

What should I check next?

thanks Chris
 
Was it a OEM plunger you put in? There was a thread last week where someone replaced their contacts and plunger, and then had problems. The plunger they put in was too long and caused problems. I never checked back in on the thread to see if the plunger was OEM or not.
 
After my LC would get to operating temperature it would not start until it cooled down a bit. I would hear a faint "click" at every key turn and all of the dash lights would come on.

Changed out my original starter with a remanufactured OEM and have not had any starting problems since (going on week 3).

Riley
 
I bought the rebuild kit and had the shop who repairs the car rebuild the starter, hmmm. Good chance they installed the plunger was too long. But would it work for a while then cause problems?

thanks
 
Was it a OEM plunger you put in? There was a thread last week where someone replaced their contacts and plunger, and then had problems. The plunger they put in was too long and caused problems. I never checked back in on the thread to see if the plunger was OEM or not.

That was me....like last month. :lol:

It was an OEM plunger, but for a 1FZ starter, not a 3FE starter. Haven't had problems since I put the old one back in... :doh:
 
How old is the battery, have it checked and check your connections to both the battery and starter.
 
battery(interstate) is pretty new. The guage is reading a consistant half mark (15volts).
I havent had time check the connections yet, I also plan to run a jumper wire from battery directly to contact on the starter to eliminate a electrical/ignition issue.
 
I have the starter off the truck. Everything looks pretty good. I am not following on what/where the "plunger" is. The SM doesnt list any part called the plunger. The motor contacts/brushes looks clean.The gear rotates clowise and locks counter clockwise. So where is the plunger, apparently a few have told me this can be tool long and may need to be shortened?

I will test ohm/continuity per the SM.

Thanks
 
Plunger pic from FAQ.

plunger.jpg
 
hmm. I took apart the motor/armature side last night and didnt get to the other half, must be in there.
Anyone know the part name for this, SM mentions nothing about or illustrates a plunger???
 
Well, with a new starter all I get is a "CLICK" nothing else.
I am frustrated!!!
Anything I overlooked???
 
Yup, Toyota reman.
I was following old posts late last night and found a 8 page post that Roncrusier posted(am at work and dont have the time to locate the link right now). After rebuilds of starter, solenoids, contacts, positive cable changeouts, etc . Ended up the culprit was the ignition switch.

I dont want to keep chasing parts, but the battery is good, checked all the fuses(strong head lights, dash lights and horn).
Can anyone back my thinking that its the ignition switch? My concern is I am getting charge to the solenoid(thus the click - one click) an the click I get a hummmm so I know theres power getting to the starter so ruling out bad cable or bad contacts at the battery terminal.

The battery contacts are clean, I bought some of the red spray gunk that prevents corrosion on the battery posts, etc.
 
Back
Top Bottom