Some trouble down shifting.

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 3, 2006
Threads
47
Messages
217
Location
Southwest, MO
I haven't gotten to drive my 40 much yet since I bought it, but the couple of times I've had it on the road I have some trouble down shifting it seems I have to slow down more than I should to get the gear. I'm wondering if I'm supposed to double clutch the thing or what. It is better going up, but there seems to be a little force in needed there too. Is this normal, or do I have something going out?

'78 factory 2f and 4spd 88k miles (for sure)
 
clutch may need replacement - hard shifting often happens before it starts slipping...

The PO told me he had just put a clutch in it. Now I know he could have just told me that, but he has helped me out with all my questions since I bought it and seems like a stand up guy.
 
did he replace the spigot bearing?

I have no idea. He told me he just had a clutch professionally installed.

What does the spigot bearing do? And where is it located. I have yet to get a FSM.
 
If all of the above fails?... Try a thinner viscosity lube oil... thicker tends to drag moving components.. more so in cooler temps... and who knows the last time it was changed?
 
Ok, I drove it some more today. It seems the hardest from 2nd to 1st. Could this be just because 1st is so low. If I double clutch the shifts seem easier. Fluid level is good.
 
checking your fluids and doing some maintenance is not a bad idea...but down shifting a cruiser takes finesse...its not a sports car...you will definately have to let the R's come down or double clutch it...but even double clutching isnt gonna help as much as just being patient and waiting until the tranny wants to be down shifted...and dont even bother shifting it back into first gear unless your almost stopped...your 4 speed first gear was meant to be a granny gear...i know lots of guys that dont even use it for normal driving...here are the gear ratios

1st gear in a 3 speed=2.79
1st gear in either 4 speed 3.56/4.93
2nd gear in either 4 speed 2.29/2.64

so you can see 1st gear is a little steeper then you need for down shifting in a corner..use it for just just starting out or trail riding
 
Have you rebuilt the clutch master cyclinder or slave cylinder ever? They are easy to rebuild.

I have no idea if either has been rebuilt. I am guessing no, I think he would have told me about it.

That makes sense about the granny gear because that is where the most trouble seems to be. 3rd to 2nd is easier than 2nd to 1st for sure.

Just be clear I'm not having to ape on the stick to get it in, when I'm slow enough it will go in, it just seems that I'm having to go slower than I should to get it in.

This is my first fj and the only one I have been around, so if that seems normal to some of you let me know...I have nothing to compare to.
 
I had the same problem but mine was from 3rd to 2nd as well as 2nd to 1st. I also have over 300k miles on the cruiser. I was told by a local tranny guy that it may be the synchro's.. and he wanted $2400 to rebuild it. Found a good used one, installed it and now I don't have the problem. Still have the same clutch, slave, pilot bearing, etc..
 
Sounds like it works perfect to me, you are just not used to the quirks of a cruiser yet. I'll trade you for my 3 speed. Not only do you have to be stopped to get into first, but you have to row into second with the clutch in before you go to first or a-grinding you will go :crybaby:
 
I've got a 3 speed too, it took me a while to understand how to shift the thing, especially since my DD is late 90's beemer. Just keep driving it and eventually you'll get comfortable with it or at least that is what worked for me.
 
Back
Top Bottom