Single Leaf spring with Spring shock obsorber ?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 19, 2012
Threads
27
Messages
89
Location
san francisco
Folks,

I need some expert advice. I wanted to make my FJ40 as soft ride as possible for daily driver.

Here is what I wanted to do .. I want to keep just one leaf spring and get a good Spring shock obsorber.

Am I crazy or this can be done ?

I dont want to built link suspension... and I don't like leaf springs... so I started searching and end up with these pictures.....

Can this be on done on FJ40.. I will keep the longest leaf and get spring shock obsorber. If yes .. any ideas which spring shock obsorber will do the job here.
RC4Z-C0049-9.webp
RC4Z-C0049-9.webp
RC4Z-C0049-8.webp
 
Major axle wrap. Load carrying stress on the shock mount. Short spring life. (sagging, S curving and eventually snapping). If (when) that single leaf fails... your axle is gonna go places you will not like. You will not find a "spring over shock absorber" that will make up for the loss of all those leaves either.

Bad idea from the get go. and no reason to do it. you can get softer than you will ever want with regular leaf springs.

and...

You OEM springs are not stiff. especially old ones. Your harsh ride is more likely due to the springs bottoming out because they are not firm enough anymore. slamming onto the bump stops does not make for a soft ride.

Mark...
 
Major axle wrap. Load carrying stress on the shock mount. Short spring life. (sagging, S curving and eventually snapping). If (when) that single leaf fails... your axle is gonna go places you will not like. You will not find a "spring over shock absorber" that will make up for the loss of all those leaves either.

Bad idea from the get go. and no reason to do it. you can get softer than you will ever want with regular leaf springs.

and...

You OEM springs are not stiff. especially old ones. Your harsh ride is more likely due to the springs bottoming out because they are not firm enough anymore. slamming onto the bump stops does not make for a soft ride.

Mark...
Thanks Mark..... that is a strong no......I think I should avoid it. I appreciate your input.
 
One approach I have been happy with, is an SOA conversion using the reverse arch springs from the front end of a squarebody Chevy truck. You can wind up with as little as 2-3 inches of lift and a much smoother ride that the OEM springs can give.


Mark...
 
Mark hit exactly the points I would make.

You can end up with a low lift, high articulation, soft riding leaf spring setup fairly easily.

Here is one of my FJ55s on 99 Tahoe rear leaf springs and leaf spring sliders front and rear:
20160128_112242-jpg.1208931

I believe I can remove another leaf from the front pack. This setup ended up being about 1-2" lower than using the stock FJ55 springs sprung over.

Here is the flex that is 'stopped' by fender contact and drag link being pinned by the leaf spring:
View attachment 1972559

With a stock FJ55 sway bar in the rear, it rides soft as a Cadillac and handles amazingly well on the mountain back roads. Here is a stable 75mph:
View attachment 1972563

As an alternative to the leaf spring sliders, I would do a shackle through the front of the frame set at about 45 degrees with full vehicle weight on it and ~1" space between frame and leaf spring eye.


Thanks Lil John... awesome ride you got there. Thanks for your input.
 
What about reducing a couple leaves and using airbags at all corners? Adjustable lift, soft ride? Would carry more weight than a strut design. Mark? Doable?
 
Just so long as you keep a strong enough spring to resist spring wrap (every day back and forth flexing every time you accelerate and brake, not just the major stuff from climbing steps and the like). And remember those leaves also locate the axle against side to side forces too.
We are planning to do airbags and *slightly* softer springs on a couple of our rigs that see heavy use ever hunting season. We have come out with over 1500 lbs of meat in the back of a rig beyond what it went into camp with. That can be tough to carry down the train with any springs that are not gonna be overly harsh when unladen. Airbags seem to be the answer for us. Just have to let it work its way up the priority list. We are just looking at the rear end right now. that is where the load changes the moist. and there is a lot more room to work wit back there than up front.

Mark...
 
Here is what I wanted to do .. I want to keep just one leaf spring and get a good Spring shock obsorber.

Am I crazy or this can be done ?

I dont want to built link suspension... and I don't like leaf springs... so I started searching and end up with these pictures.....
Your pictures are from RC car.

If you want to remove leafs you’ll need build traction bars to prevent axle wrap as mentioned few times.
1973128
 
Back
Top Bottom