side's and spiders are gone.

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 9, 2002
Threads
247
Messages
1,207
Location
Utah
i don't know if it happened when the rear pinion bearing went out, but i've got some nice chips on the little gears. i'm thinking it might be time to toss in the locker and forget about trying to replace the suckers.

my old man is talking about us getting an ARB in there now.....
maybe it's time. it still has the 4.10's in it.
 
maybe i'll put the front gears into the rear, then put a locker up front. wouldn't it be better to run a locker up front?
an arb would be cool, but maybe an aussie. either way, i think i would rather run it in the front axle for pulling.
i'm sure this has been debated in other threads.
 
yes it has been talked about. I think like 8 out of 10 people would disagree with putting it in the front of a stock fj40. My vote goes to rear aussie or arb and arb only for front.
 
i'd take the aussie over the lockright since i know many who've broken lockrights and no one who's broken an aussie (butthey are a young locker based on old technology, so i guess anything's possible). ideally an arb,but $$$
 
Last edited:
Aussie Locker

projektdotnet said:
Franky40's whole crew runs rear lockrites and has had no problems. The one of them that ran the aussie actually managed to break it. I know that aussie is still a good locker none-the-less but I'm going with the lockrite myself.

We have many thousands of Aussie Lockers in service and we have yet to have anyone return an Aussie Locker for warranty replacement that was physically broken. We have seen improper installations break pins, but we have never seen an Aussie Locker where the locker itself was broken. If this has happened no customer has ever informed us of this and we would immediately replace the locker with a new one on receipt of the damaged locker. We would appreciate anyone with a broken locker to contact me personally at bill@offroadlockers.com so we can see the locker.
 
Land Cruiser Aussie Lockers

isotel said:
i just got an e-mail from them, they had a "Few" in stock, they are all gone now :frown:

i guess its another 2 weeks till they get a larger shipment

Wow, those went quickly. There are three still in stock and the web site has been corrected to reflect that number.
 
Aussie_Locker said:
We have many thousands of Aussie Lockers in service and we have yet to have anyone return an Aussie Locker for warranty replacement that was physically broken. We have seen improper installations break pins, but we have never seen an Aussie Locker where the locker itself was broken. If this has happened no customer has ever informed us of this and we would immediately replace the locker with a new one on receipt of the damaged locker. We would appreciate anyone with a broken locker to contact me personally at bill@offroadlockers.com so we can see the locker.
I personally have never met him and I don't even know his name. It was a friend of a friend of a friend kinda thing. I do belive it was improper backlash IIRC (broken pins as you say). We don't have the tools up at our shop to do it properly whereas the lockrite supposedly doesn't need this adjusting. I'm not the tech guys there i'm just a young grasshopper.
 
Aussie Locker

projektdotnet said:
I personally have never met him and I don't even know his name. It was a friend of a friend of a friend kinda thing. I do belive it was improper backlash IIRC (broken pins as you say). We don't have the tools up at our shop to do it properly whereas the lockrite supposedly doesn't need this adjusting. I'm not the tech guys there i'm just a young grasshopper.


Just for the record, the Aussie Locker and the Lock Right are installed the same and there are no adjustments in either. The spacer to cross shaft and the inner-cam spacings must be within specification for both. The difference between the two lockers is in design, the material used, the manufacturing process, heat treat process and the quality control. We have a warranty that covers our product no matter what size tires you use or the horsepower of your vehicle and they have limitations.

We still have never seen a broken Aussie Locker.
 
Aussie_Locker said:
We have many thousands of Aussie Lockers in service and we have yet to have anyone return an Aussie Locker for warranty replacement that was physically broken. We have seen improper installations break pins, but we have never seen an Aussie Locker where the locker itself was broken. If this has happened no customer has ever informed us of this and we would immediately replace the locker with a new one on receipt of the damaged locker. We would appreciate anyone with a broken locker to contact me personally at bill@offroadlockers.com so we can see the locker.

I've been running one of the early Aussie Lockers (thanks for getting me the correct spacers ASAP Bill!) out back with an ARB up front and I've never had a problem.
The Aussie replaced a broken EZ-Locker and a Lockright. And I drive this thing to most events.
 
Not Back Ordered, Yeah

I ordered my Assuie Locker back in April, Got an e-mail on the 12th June said it was sent on the 13th June, now it is 19th of June and still NO LOCKER.

Bet Assuie now regrets posting that No back-order note.

Michael (still waiting)
 
Back
Top Bottom