Shaking in front after work completed - Advice

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 27, 2016
Threads
23
Messages
117
Location
Georgia
I was having some steering problems so I took it to a shop for some work. Now I get some serious shakes when I get around 35 mph, then even bigger shakes at 60 mph. Odd thing is it gets loud when I let off the gas when I'm slowing down from 60 mph. Here's what was done:
- Replaced sway bar
- Driver side front hub/wheel bearing adjusted
- Rewelded driver side leaf spring hanger welded to frame.

Any advice on what could be the problem? I have an old man lift kit. It didn't do this at all prior to work.
 
How are your tires?
I've read threads here on mud where some guys went to the end of the earth trying to fix vibration at speed. Doing all the hard mechanical fixes that might solve this he problem... only to eventually find out that a new set of tires was the answer.
 
How are your tires?
I've read threads here on mud where some guys went to the end of the earth trying to fix vibration at speed. Doing all the hard mechanical fixes that might solve this he problem... only to eventually find out that a new set of tires was the answer.

I read some of those threads also. Makes sense. I had my tires checked at Goodyear last week and they were in good shape. They discovered the broke shakle and sway bar being to short. Guess i'll take it back to the shop. Dang.
 
Forgot to mention I had the rear u-joints replaced. I wonder if the angle is wrong?
 
Driveshafts could be out of phase?

If there was no shake before work done, the tires ought not be blamed.
Hmm.
One bearing updated / serviced, the other side not?
 
Driveshafts could be out of phase?

If there was no shake before work done, the tires ought not be blamed.
Hmm.
One bearing updated / serviced, the other side not?

That's all they said they noticed. Watched a video about the angle of the u-joints not being zero and how that causes the shakes. Suggested adding a shim to the leaf springs. Could have raised the angle of u-joint coming off the engine by fixing the busted shackle that broke lose of the frame. Hmm, learning a lot about drive shafts today.
 
Were the replacement parts Toyota?
 
The rear differential doesn't need to point directly at the transfer case. Mine is level & I have about a 3"+ lift (compared to stock height) when the truck is empty.
No vibration at all at any speeds. Don't put any shims in the rear.

The thousand dollar question is:
Did the shop that installed the new u-joints dynamically balance the shaft after they worked on it?

If not, it's out of balance.
(but may not be causing your vibration..... but maybe)
 
Occams razor. Keep it simple.

You mention 'steering problems'.
What were they?

These vibrations and frequency seem to be based on rpm of axles / driveshafts / wheels...
after having been worked on...
 
The rear differential doesn't need to point directly at the transfer case. Mine is level & I have about a 3"+ lift (compared to stock height) when the truck is empty.
No vibration at all at any speeds. Don't put any shims in the rear.

The thousand dollar question is:
Did the shop that installed the new u-joints dynamically balance the shaft after they worked on it?

If not, it's out of balance.
(but may not be causing your vibration..... but maybe)
I'll ask them today. Thanks
 
Occams razor. Keep it simple.

You mention 'steering problems'.
What were they?

These vibrations and frequency seem to be based on rpm of axles / driveshafts / wheels...
after having been worked on...

My steering wheel would need to be turned 10 degrees to the left to keep the wheels going straight. Shop said it was because of the shackle being broke from frame and that my sway bar was too short. No vibrations before, added a longer sway bar and welded shackle back and vibrations happen now.
 
None of those parts you had worked on would cause any kind of vibration or noise besides or as much as a driveshaft would. Is it in phase or not? Was it balanced, or not?
 
None of those parts you had worked on would cause any kind of vibration or noise besides or as much as a driveshaft would. Is it in phase or not? Was it balanced, or not?

I'm a newbie and learning quickly, but I don't know what "in phase" means? Do you mean the driveshaft being balanced?
 
Also ask for an alignment spread sheet thing so you know where your caster and toe are at.

No. This is a red herring, as is anything regarding pinion angles or axle shims. Let's read the description OP provided and analyze what has been modified FIRST. If he didn't have this issue before Then it is most likely a result of one of he "repairs".

@Ellison

This is what it means for a driveshaft to be in phase.

shaftends.webp
 
Shop called today and said it was a u-joint bearing issue that will be replaced and balance the driveshaft. I'll report back after a test drive tomorrow when I pick her up.
 
No. This is a red herring, as is anything regarding pinion angles or axle shims. Let's read the description OP provided and analyze what has been modified FIRST. If he didn't have this issue before Then it is most likely a result of one of he "repairs".

@Ellison

This is what it means for a driveshaft to be in phase.

View attachment 1237770
Thank you
 
Back
Top Bottom