Second Skin Audio - 1st Impressions

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 25, 2003
Threads
720
Messages
4,293
Location
Rixeyville, VA
Certainly did not go as deep into this project as "Sully" but still covered a good amount of ground over the weekend.

The 4BTA is certainly louder then the 1FZ so some work was needed to make the truck more drivable for my purposes.

I used damplifier on both front doors. I covered both the interior and exterior skins of the doors. While i was in there, i replaced the eclipse 5.25's with the Pioneer 6.5's that many have used with high praise.

On the floors, I used one layer of damplifier, followed by 3 layers of "Spectrum".

I have not yet done anything in the cargo area, including the rear wheel wells, or the rear doors. They are on the long list....

I still haven't yet installed the carpet as i'm trying to get it cleaned nicely before it is reinstalled. The second skin products alone have made it quieter than it was before, even without the carpet! I'm anxious to see how much difference the carpet makes as well.

Now i just need to figure out how to complete the process on the firewall. I think there is alot to be gained from the firewall but so far the $200 I spent on 40sq ft of damplifier and 1 gallon on spectrum has been VERY well spent. I can only imagine how quiet an 80 with a stock motor would be.
014-1.webp
013.webp
012.webp
 
Wow nice job. I've never done anything to my floor but I gave my front doors the royal treatment with Raamat. That isn't a job for the faint of heart, take a huge amount of time to do the inner and outer door skins. Did you lay down the foil backed product on the floor then put a liquid product over it?
 
Did you use the stock speaker wires? I've been thinking about doing this as well. How much of a pain was it to remove the carpet? Timewise?
 
x2 on the Second Skin products. The quality is absolutely incredible.
 
To answer a few questions:

Yes, the foil backed material(damplifier) was placed on the floors first, then covered with the spectrum.

Unfortunately, stock speaker wires are still being used. I've removed the rear heater to make room for either an inverter or 2nd amplifier to power the speakers. I have eclipse speakers in the rear doors, an alpine head unit, and JL 10" sub powered by its own stand alone amp so the stereo does well despite some of the factory wiring that is still being used.

Carpet removal is not hard at all. I've done it twice now on this truck. Remove front/2nd row seats, remove center console and tranny hump cover, then remove door trip pieces.
 
Are you saying get under the truck and brush the stuff up against the bottom of the vehicle when you say "undercoat"?

DougM
 
Yup. Supposedly you can do that and it's supposed to work well.

When I reroute my exhaust over the frame rail I'll be using some Spectrum firewall to help with the heat toasting the rear heater lines...
 
Are you saying get under the truck and brush the stuff up against the bottom of the vehicle when you say "undercoat"?

DougM

X2 I thought he meant undercoat as in under the damplifier but now after I reread it maybe he did mean under the truck. Please verify.
 
Why did you remove the carpets the first time??? :D

Good timing B. Ive been looking at my options and already have had the carpets out. 200 is certainly cheaper than the Dynamat i was looking at for the entire floor area. Was looking at the hushmat some have used but i need the heat block as well after 3'' over the frame. How does the second skin do for heat (googling now :)) Passenger seat is toasty!

wow, doors look like no fun at all.
 
Doors are time consuming but I enjoy this type of work. Doing the interior and exterior skin of just the front doors makes a big difference especially when running an M/T.

And yes, he does mean use the spectrum as an undercoat. the stuff dries pretty nice and hard. For those who dont want to run carpet, you could probably just do an extra layer or two of spectrum like i did and call it a day. I may look into applying some spectrum as an undercoat later on, but i just don't see the marginal difference being worth it to me considering the added time it would take.

FWIW, a second skin rep did clarify that applying spectrum on top of damplifier was fine to do. Everything has dried very nicely and there are no ill effects. I wish i had the patience to remove the whole dash as alot of my engine noise is coming from there.

Lastly, the carpet were out once before for some....well, "spring cleaning"
 
I wish i had the patience to remove the whole dash as alot of my engine noise is coming from there.

I've considered adding Spectrum Firewall on the engine side of the firewall.
 
it would be cool if you could do the firewall, and I bet it would kill a ton of engine noise like you said. So that 4BT is annoyingly loud? I have noticed lots of guys selling there 4BT equipped rigs, so there must be something they don't like about them. I also heard they vibrate very badly at idle, shaking loose all kinds of components. I'm intersted to see if you can make your rig "livable" as far as being a comfortable cruiser and around town daily driver.
Also, before you put your carpet back in, you might want to entertain installing this under the carpet. RAAMaudio - Quality and Value in Automotive Sound Deadening
It's the second product down, Ensolite. This coupled with what you have already done should really knock down on the road noise. Just an extra idea since you have it all apart and clean.
 
it would be cool if you could do the firewall, and I bet it would kill a ton of engine noise like you said. So that 4BT is annoyingly loud? I have noticed lots of guys selling there 4BT equipped rigs, so there must be something they don't like about them. I also heard they vibrate very badly at idle, shaking loose all kinds of components. I'm intersted to see if you can make your rig "livable" as far as being a comfortable cruiser and around town daily driver.
Also, before you put your carpet back in, you might want to entertain installing this under the carpet. RAAMaudio - Quality and Value in Automotive Sound Deadening
It's the second product down, Ensolite. This coupled with what you have already done should really knock down on the road noise. Just an extra idea since you have it all apart and clean.

Annoyingly loud is a subjective term. In my opinion the engine is not "annoyingly loud". It is most certainly louder than the stock motor but the simple steps in this thread have already made a big difference. At idle it is fine. The stock idle does have a noticable vibration but upping the idle to 900-950 smooths it out a lot.
As with any major modification such as the 4bt swap, there are costs and benefits. I'm running a FULLY weighted FZJ80 on 35'' Toyo's and am averaging 20mpg on the highway. In 4-lo, fully locked up, the truck is laughable with how much torque is available.
Having said that, there are more comfortable, quiet, fuel efficient, small cars available for <$5000 which make DD'ing even my truck with the stock motor seem foolish.
Lastly, I've heard the comment about a lot of 4bt landcruiser being sold lately. If memory serves me right, i think 5-6 have been up for sale in the last year or two. Proffitt's alone has done 40+ conversions in the last several years so I dont see it as huge influx of converted trucks coming to the market.
 
I'm running a FULLY weighted FZJ80 on 35'' Toyo's and am averaging 20mpg on the highway.


There are a lot of good reasons for a diesel swap. Gas milage isn't much of one anymore since diesel (at least around here) is significantly more expensive than regular.


Now all that torque...that I could get behind. :D
 
thanks for the input, as I was starting to not consider a 4bt swap. When my stock gasser hits the end of it's life, or when I have a good chunk of expendable cash, I'd really like to persue the diesel route. Running a Cruiser on WVO or Biodiesel would be really neat to me.
 
thanks for the input, as I was starting to not consider a 4bt swap. When my stock gasser hits the end of it's life, or when I have a good chunk of expendable cash, I'd really like to persue the diesel route. Running a Cruiser on WVO or Biodiesel would be really neat to me.

As you should. Overall, i really like the diesel. If i did it again, i might look at other options for a "newer" diesel. The 4bt is good in its own respects but i think most people who come from the smooth, quiet 1fz will find a quieter diesel better for them.
 
There are a lot of good reasons for a diesel swap. Gas milage isn't much of one anymore since diesel (at least around here) is significantly more expensive than regular.


Now all that torque...that I could get behind. :D

i would love the 4bt
20mpgs is double what a 1FZ in similar state gets. That is huge.

around here Diesel is hovering right around mid grade petrol so it would be gravy

overall it would be fun to have and the 4bt benefits are ones i'd like ... someday!
 
X2 I thought he meant undercoat as in under the damplifier but now after I reread it maybe he did mean under the truck. Please verify.

Yes.
As an undercoating.
Under the truck.
To sandwich the floor pan with Damplifier Pro on the cabin side of the floor pan and Spectrum on the outside, under the truck.

Hope that helps!

ANT
 
Back
Top Bottom